Nortel Networks 555-7101-217, P0605618 manual CallPilot server

Page 69

May 2003

Installing the server and connecting the peripheral devices

Before you connect the server to the power source, review the following diagram to ensure that all peripheral hardware devices are in place.

CallPilot server

Mouse

Keyboard

RJ-45 RJ-45








Monitor		ELAN hub		CLAN hub
		(M1 or		(optional)
		CSE 1000
		only)
AC		AC		AC
power		power		power

		AC
		power
		source

RS-232

Modem

AC power

G101637

Note: For details on the DC power source for 1001rp DC servers, see Chapter 3, “Power supply installation.”

Part 2: 1001rp Server Hardware Installation

69

Image 69

Contents CallPilot P0605618 CallPilot Page Publication history Publication history Contents Installing the server and connecting the peripheral DevicesIndex A p t e r 1001rp server descriptionServer dimensions and weight Server featuresIntroduction 49.5 cm 19.5Alarm board Front panel features front view without the front bezelRear panel diagram Overhead view of empty server showing PCI and ISA connectors Slot assignments Slot definition and slot numbering1001rp slot assignments Reserved for COM1 COM2 I/O bracket Slot Single Board Computer SlotElan Network card Slot Clan Network card Slot 12bBRD20 IRQ mapping table IRQ Network connectivity Customer LAN optional Sample network setup MeridianTelephony LAN/Customer LAN 10/100BaseT or 100BaseT Sample network setup Succession CSECallPilot Elan and Clan network setup Switch connectivityNetwork requirements Remote access connectivityModem Kbps external modem NTRH9078 provides Supported peripheral devicesSince the modem is an external device, it requires its own Also supported, but has been replaced by the 56 KbpsPreparing for installation Installation checklist Installation overviewMay 2003Preparing for installation Conventions for warnings Follow this procedure to unpack the server and peripherals Unpacking the 1001rp serverTo unpack the equipment What’s next? About the front bezel doors Removing the front bezel and server coverTo remove the front bezel To remove the server cover High current inside the chassis can cause severe injuryContinue with Inspecting the server interior on To replace the front bezel after installation is complete To inspect the server interior Inspecting the server interiorPreparing for installationStandard Power supply installation Safety precautions Safety informationEquipment handling guidelines Section a Installing the power supply modules AC or DC Installing the second power supply module AC or DC About the power supply moduleAC versus DC systems Power supply modules Do one of the following To install the power supply moduleSection B Setting up DC power source for a 1001rp DC server DC wire gauge tables Metric wire conversion DC rack cabling Following diagram shows typical rack power cabling48VDC power distribution rationale Multiple PDUs About the Power Distribution UnitDC power input PDU terminal blocks and wiring diagramTo bring DC power and ground into the PDU Bringing power and ground into the PDUMay Power supply installation Installing the server and connecting the peripheral devices To install the server Installing the serverRequired equipment Preparing the modemDIP Modem DIP switchesTo set the modem DIP switches OFF Loads Y or Y1 configuration from OFF The modem sends a CD signal when itAT command set recognition OFF Disables command recognition dumbRear panel connections Connecting peripherals to the serverTo connect the modem to the server To connect the mouse, keyboard, and monitor to the serverContinue with Connecting the server to the Elan on Connecting the server to the Elan Media Access Control addressTo connect the server to the Elan Feature key adapter dongle. See To connect the server to the Clan Connecting the server to the Clan optionalWhat’s next? Installing the Nortel Networks software feature key adapter For installation, you require a Phillips No screwdriver To install the software feature key adapterContinue with Connecting the server to power on RequirementsBefore you begin Connecting the server to powerCallPilot server To connect the 1001rp AC server to power Connect the DC power cable to the server, as shown below To connect the 1001rp DC server to powerTo start the server Binder Installing the server and connecting the peripheral devices Index Clan Elan May Index Index Page Product release Document release Standard Date May