Nortel Networks 555-7101-217, P0605618 manual Index

Page 75

Index

A

adapter

software feature key, illustration 66 alarm board 11

assigned board label CallPilot Manager 16

C

checklist installation 26

CLAN

media access control address 64 CLAN network card faceplate 64 connecting peripherals to the server 59 connecting the server 68 connectivity

Ethernet 22 remote 23 Customer LAN

see CLAN 64

D

DC power 47

DC power and ground 50 DC power input 49

DC wire gauge tables 44 devices, peripheral

Ethernet hub 24 keyboard 24 modem 24

monitor 24 mouse 24

diagram connection

network, M1 and CallPilot server 20 network, Succession CSE and CallPi-

lot server 21

front panel 11

PCI and ISA connectors 13 rear panel

slot locations 12

server connections for the power cord and peripherals 59

DIP switches modem, function 57

DIP switches, setting modem 57

dongle 66

doors on the front bezel 31

E

ELAN

Media Access Control address 62 equipment

unpacking 29 Ethernet hub

description 24

F

fax modem illustration 56

Part 2: 1001rp Server Hardware Installation

75

Image 75

Contents CallPilot P0605618 CallPilot Page Publication history Publication history Contents Installing the server and connecting the peripheral DevicesIndex A p t e r 1001rp server description49.5 cm 19.5 Server featuresServer dimensions and weight IntroductionAlarm board Front panel features front view without the front bezelRear panel diagram Overhead view of empty server showing PCI and ISA connectors Slot assignments Slot definition and slot numbering1001rp slot assignments Clan Network card Slot 12b Single Board Computer SlotReserved for COM1 COM2 I/O bracket Slot Elan Network card SlotBRD20 IRQ mapping table IRQ Network connectivity Customer LAN optional Sample network setup MeridianTelephony LAN/Customer LAN 10/100BaseT or 100BaseT Sample network setup Succession CSECallPilot Elan and Clan network setup Switch connectivityNetwork requirements Remote access connectivityAlso supported, but has been replaced by the 56 Kbps Supported peripheral devicesModem Kbps external modem NTRH9078 provides Since the modem is an external device, it requires its ownPreparing for installation Installation checklist Installation overviewMay 2003Preparing for installation Conventions for warnings Follow this procedure to unpack the server and peripherals Unpacking the 1001rp serverTo unpack the equipment What’s next? About the front bezel doors Removing the front bezel and server coverTo remove the front bezel To remove the server cover High current inside the chassis can cause severe injuryContinue with Inspecting the server interior on To replace the front bezel after installation is complete To inspect the server interior Inspecting the server interiorPreparing for installationStandard Power supply installation Safety precautions Safety informationEquipment handling guidelines Section a Installing the power supply modules AC or DC Installing the second power supply module AC or DC About the power supply moduleAC versus DC systems Power supply modules Do one of the following To install the power supply moduleSection B Setting up DC power source for a 1001rp DC server DC wire gauge tables Metric wire conversion DC rack cabling Following diagram shows typical rack power cabling48VDC power distribution rationale Multiple PDUs About the Power Distribution UnitDC power input PDU terminal blocks and wiring diagramTo bring DC power and ground into the PDU Bringing power and ground into the PDUMay Power supply installation Installing the server and connecting the peripheral devices To install the server Installing the serverRequired equipment Preparing the modemDIP Modem DIP switchesTo set the modem DIP switches OFF Disables command recognition dumb OFF The modem sends a CD signal when itOFF Loads Y or Y1 configuration from AT command set recognitionRear panel connections Connecting peripherals to the serverTo connect the modem to the server To connect the mouse, keyboard, and monitor to the serverContinue with Connecting the server to the Elan on Connecting the server to the Elan Media Access Control addressTo connect the server to the Elan Feature key adapter dongle. See To connect the server to the Clan Connecting the server to the Clan optionalWhat’s next? Installing the Nortel Networks software feature key adapter Requirements To install the software feature key adapterFor installation, you require a Phillips No screwdriver Continue with Connecting the server to power onBefore you begin Connecting the server to powerCallPilot server To connect the 1001rp AC server to power Connect the DC power cable to the server, as shown below To connect the 1001rp DC server to powerTo start the server Binder Installing the server and connecting the peripheral devices Index Clan Elan May Index Index Page Product release Document release Standard Date May