Nortel Networks 555-7101-217 Single Board Computer Slot, Reserved for COM1 COM2 I/O bracket Slot

Page 15

May 20031001rp server description

	CallPilot-
Slot	assigned board
number	labela	Meridian 1	Succession CSE 1000

Slot 3	BRD03	Not used	Not used

Slot 4	BRD04	Not used	Not used

Slot 5	BRD05	Not used	Not used

Slot 6	BRD06	Not used	Not used

Slot 7	BRD07	Not used	Not used

Slot 8	BRD08	Single Board Computer	Single Board Computer

Slot 9	BRD09	Reserved for COM1 and	Reserved for COM1 and
		COM2 I/O bracket	COM2 I/O bracket

Slot 10	BRD10	ELAN Network card	ELAN Network card

Slot 11	BRD11	CLAN Network card	CLAN Network card

Slot 12b	BRD12	MPB16-4 board #1	MPB16-4 board #1

Slot 13	BRD13	MPB16-4 board #2	MPB16-4 board #2
		(optional)	(optional)

Slot 14	BRD14	Not used	Not used

Slot 15	BRD15	Not used	Not used

Slot 16	BRD16	Not used	Not used

Slot 17	BRD17	Not used	Not used

Slot 18	BRD18	Not used	Not used

Slot 19	BRD19	VGA card (monitor	VGA card (monitor
		connection)	connection)

Part 2: 1001rp Server Hardware Installation

15

Image 15

Contents CallPilot P0605618 CallPilot Page Publication history Publication history Contents Installing the server and connecting the peripheral DevicesIndex A p t e r 1001rp server description49.5 cm 19.5 Server featuresServer dimensions and weight IntroductionAlarm board Front panel features front view without the front bezelRear panel diagram Overhead view of empty server showing PCI and ISA connectors Slot assignments Slot definition and slot numbering1001rp slot assignments Clan Network card Slot 12b Single Board Computer SlotReserved for COM1 COM2 I/O bracket Slot Elan Network card SlotBRD20 IRQ mapping table IRQ Network connectivity Customer LAN optional Sample network setup MeridianTelephony LAN/Customer LAN 10/100BaseT or 100BaseT Sample network setup Succession CSECallPilot Elan and Clan network setup Switch connectivityNetwork requirements Remote access connectivityAlso supported, but has been replaced by the 56 Kbps Supported peripheral devicesModem Kbps external modem NTRH9078 provides Since the modem is an external device, it requires its ownPreparing for installation Installation checklist Installation overviewMay 2003Preparing for installation Conventions for warnings Follow this procedure to unpack the server and peripherals Unpacking the 1001rp serverTo unpack the equipment What’s next? About the front bezel doors Removing the front bezel and server coverTo remove the front bezel To remove the server cover High current inside the chassis can cause severe injuryContinue with Inspecting the server interior on To replace the front bezel after installation is complete To inspect the server interior Inspecting the server interiorPreparing for installationStandard Power supply installation Safety precautions Safety informationEquipment handling guidelines Section a Installing the power supply modules AC or DC Installing the second power supply module AC or DC About the power supply moduleAC versus DC systems Power supply modules Do one of the following To install the power supply moduleSection B Setting up DC power source for a 1001rp DC server DC wire gauge tables Metric wire conversion DC rack cabling Following diagram shows typical rack power cabling48VDC power distribution rationale Multiple PDUs About the Power Distribution UnitDC power input PDU terminal blocks and wiring diagramTo bring DC power and ground into the PDU Bringing power and ground into the PDUMay Power supply installation Installing the server and connecting the peripheral devices To install the server Installing the serverRequired equipment Preparing the modemDIP Modem DIP switchesTo set the modem DIP switches OFF Disables command recognition dumb OFF The modem sends a CD signal when itOFF Loads Y or Y1 configuration from AT command set recognitionRear panel connections Connecting peripherals to the serverTo connect the modem to the server To connect the mouse, keyboard, and monitor to the serverContinue with Connecting the server to the Elan on Connecting the server to the Elan Media Access Control addressTo connect the server to the Elan Feature key adapter dongle. See To connect the server to the Clan Connecting the server to the Clan optionalWhat’s next? Installing the Nortel Networks software feature key adapter Requirements To install the software feature key adapterFor installation, you require a Phillips No screwdriver Continue with Connecting the server to power onBefore you begin Connecting the server to powerCallPilot server To connect the 1001rp AC server to power Connect the DC power cable to the server, as shown below To connect the 1001rp DC server to powerTo start the server Binder Installing the server and connecting the peripheral devices Index Clan Elan May Index Index Page Product release Document release Standard Date May