Nortel Networks 555-7101-217, P0605618 manual May Index

Page 77

May 2003

Index

AC server 70 DC server 71

power distribution rationale 47 Power Distribution Unit

See PDU power guidelines 44 power supply

bringing power and ground into the PDU

50

DC wire gauge tables 44 grounding guidelines 44 Metric wire conversion 45 module installation 42 module location 40 overview 40

PDU 48

power distribution rationale 47 protocols, supported network 22

R

remote access connectivity 23

removing front bezel 32 server cover 33

replacing server cover 36

S

safety information 38

serial number of the server 66 server

connecting peripherals 59 power connection 68 serial number 66

setting

modem DIP switches 57 slot assignments 14

slot definition 14 slot numbering 14

software feature key 66

Succession CSE 1000 and CallPilot server network diagram 21

switches, setting DIP modem 57

T

tables, slot assignment 14 telephony LAN

See TLAN TLAN

illustration 21

U

unpacking equipment 29

Part 2: 1001rp Server Hardware Installation

77

Image 77

Contents CallPilot P0605618 CallPilot Page Publication history Publication history Contents Index Installing the server and connecting the peripheralDevices A p t e r 1001rp server descriptionServer dimensions and weight Server featuresIntroduction 49.5 cm 19.5Alarm board Front panel features front view without the front bezelRear panel diagram Overhead view of empty server showing PCI and ISA connectors 1001rp slot assignments Slot assignmentsSlot definition and slot numbering Reserved for COM1 COM2 I/O bracket Slot Single Board Computer SlotElan Network card Slot Clan Network card Slot 12bBRD20 IRQ mapping table IRQ Network connectivity Customer LAN optional Sample network setup MeridianTelephony LAN/Customer LAN 10/100BaseT or 100BaseT Sample network setup Succession CSECallPilot Elan and Clan network setup Switch connectivityNetwork requirements Remote access connectivityModem Kbps external modem NTRH9078 provides Supported peripheral devicesSince the modem is an external device, it requires its own Also supported, but has been replaced by the 56 KbpsPreparing for installation Installation checklist Installation overviewMay 2003Preparing for installation Conventions for warnings To unpack the equipment Follow this procedure to unpack the server and peripheralsUnpacking the 1001rp server What’s next? About the front bezel doors Removing the front bezel and server coverTo remove the front bezel Continue with Inspecting the server interior on To remove the server coverHigh current inside the chassis can cause severe injury To replace the front bezel after installation is complete To inspect the server interior Inspecting the server interiorPreparing for installationStandard Power supply installation Equipment handling guidelines Safety precautionsSafety information Section a Installing the power supply modules AC or DC AC versus DC systems Installing the second power supply module AC or DCAbout the power supply module Power supply modules Do one of the following To install the power supply moduleSection B Setting up DC power source for a 1001rp DC server DC wire gauge tables Metric wire conversion DC rack cabling Following diagram shows typical rack power cabling48VDC power distribution rationale Multiple PDUs About the Power Distribution UnitDC power input PDU terminal blocks and wiring diagramTo bring DC power and ground into the PDU Bringing power and ground into the PDUMay Power supply installation Installing the server and connecting the peripheral devices To install the server Installing the serverRequired equipment Preparing the modemDIP Modem DIP switchesTo set the modem DIP switches OFF Loads Y or Y1 configuration from OFF The modem sends a CD signal when itAT command set recognition OFF Disables command recognition dumbRear panel connections Connecting peripherals to the serverTo connect the modem to the server To connect the mouse, keyboard, and monitor to the serverContinue with Connecting the server to the Elan on To connect the server to the Elan Connecting the server to the ElanMedia Access Control address Feature key adapter dongle. See To connect the server to the Clan Connecting the server to the Clan optionalWhat’s next? Installing the Nortel Networks software feature key adapter For installation, you require a Phillips No screwdriver To install the software feature key adapterContinue with Connecting the server to power on RequirementsBefore you begin Connecting the server to powerCallPilot server To connect the 1001rp AC server to power Connect the DC power cable to the server, as shown below To connect the 1001rp DC server to powerTo start the server Binder Installing the server and connecting the peripheral devices Index Clan Elan May Index Index Page Product release Document release Standard Date May