SATO ct4i manual Ribbon Loading, Ribbon Take-up Spindle

Page 31

Unit 3: Installation

RIBBON LOADING

This chapter provides guidance on how to station, connect, and load the printer once unpacked. Following printer setup, proceed to the next chapter for information on interface selection.

1

Get the media ready. The label roll is optional in this procedure.

Ribbon

Take-up

Spindle

Load the ribbon core into the take- up spindle.

2

Raise the ribbon loader assembly as shown here.

Turn the the take-up spindle to reduce any slack in the ribbon.

3

Ribbon

Supply

Spindle

Load the ribbon roll (shiny side up) into the supply spindle from underneath (see blue arrow).

Ribbon loading is now complete. The loading path is as depicted.

Figure 3-3b, Ribbon Loading

NOTES

1.For best printing results and minimal operational problems, use only genuine SATO-approved combinations of ribbon and labels.

2.Beware of injury when lifting or closing the printer covers.

3.Remove the label and ribbon media before transporting the printer.

4.For ribbon widths of 76 mm/59 mm/45 mm, insert the supplied Core Adapter into the core of the ribbon roll before loading it into the printer.

5.The ribbon loading assembly can be stowed away inside the top cover and held in place by the black plastic latching mechanism (see “general description” on page 1-3)

6.Do extended test prints of specific combinations of ribbon and label media before purchasing them for volume usage.

7.If an optional cutter is installed, be sure to keep your hands away from the cutter blade when attempting to load or adjust media.

CT4i Series Operator Manual

3-7

Image 31
Contents Operator Manual Sato America, Inc Table of Contents Cleaning Procedures MaintenanceSato group of Companies Introduction Personal Injury About this ManualCT4i Series Operator Manual General DescriptionThis page is left blank intentionally Technical Data Processing Physical CharacteristicsPower Supply Environmental Excluding MediaRibbon PrintSensing MediaDownloadable Fonts Character Font CapabilitiesRegulatory Matrix FontsBarcode Capabilities Interface Selection Interface SpecificationsDB25P Signals PIN#Printer Host PIN Assignments Signal Direction SpecificationsUniversal Serial BUS USB Software Specifications802.11G Wireless LED Indicator StatusWireless LAN Signal Strength Socket Connection Diagram Receive Buffer Control Interface SignalsSignal Signal Definition Cable Requirements DB9 Host Direction PrinterCT4i Series Operator Manual CT4i Series Operator Manual This page is intentionally left blank Installation Overview Electrical Precautions Printer Placement TipsGeneral Precautions Unpacking & Parts Identification Unpacking & Parts IdentificationMedia Loading Rolled Paper Printer InstallationSite Location Media SelectionRibbon Take-up Spindle Ribbon LoadingFanfold paper loading Loading Fanfold PaperLabel Sensing Printer Label Sensor PositioningOperational Mode Selection Label Print Direction This page is intentionally left blank Printer Configuration Operating Panel Configuration ModesFanfold-label Loading Slot Rear PanelDIP Switch Settings Configuration PanelLED Switch 4 DT/TT Mode DIP Switch Settings CONT’DSwitch 5 Head Check Switch 7 Data Dump Switch 6 VR1 Potentiometer Adjustment modeSwitch 8 Interface Board selection Operational Modes Power on sequence for various Operational ModesNormal Mode LED and Buzzer status during Normal Mode operationOperational Modes CONT’D Data found on Test Prints User Test Print Mode Feed + Power onData Printed Default Settings Mode Online + Feed + Power on Parameter Default SettingHEX Dump Mode Power on with DSW7=ON Settings AffectedDSW5 DSW6 DSW8 Function Online Error Buzzer LEDProgram Download Mode DSW1=ON, DSW2=OFF, DSW3=ON + Power on Font Download Mode DSW1=OFF, DSW2=ON, DSW3=ON + Power onCause Errors during Font and Program Download ModesOffsets Mode Length of Offset mm Print head resolutionMoved with Leading Edge Positive + Offset Potentiometer AdjustmentsPitch Offset Original First Line Print PositionPrint Darkness Potentiometer Adjustments CONT’DData Dump Diagnostic Label Printing Test Labels Printing FACTORY/SERVICE Test Prints CT4i Series Operator Manual Troubleshooting Error Troubleshooting GuideBlinks Uneven Print Darkness Image VoidsRibbon Wrinkling Light Print ImagesSmeared Print Images No Printed ImagePrinter Creates a Blank Label Incorrect Label PositioningCHK Troubleshooting Step Interface TroubleshootingLAN Ethernet Interface HEX Dump Test Print TroubleshootingTest Label Printing Maintenance Print Head Replacement Cleaning ProceduresAdjusting the Print Quality Adjustment ProceduresPrint Speed Cleaning the Print Head Cleaning the Print HEAD, Platen and RollersClearning Stubborn Debris on the Print Head Cleaning the Platen and Paper Roller Cleaning the Print HEAD, Platen and Rollers CONT’DRELEASING/REPLACING the Print Head Cleaning the Sensor CT4i Series Operator Manual Sato Group of Companies Asia Pacific & Oceania Region Sato Group of Companies