SATO ct4i manual Physical Characteristics, Environmental Excluding Media, Power Supply, Processing

Page 10

		Unit 2: Technical Data

PHYSICAL CHARACTERISTICS

Width		7.8 in. (198 mm)
Height		8.8 in. (225 mm)
Depth		7.1 in. (180 mm)
Weight		5.5 lbs (2.5 Kg) excluding AC adaptor

ENVIRONMENTAL (EXCLUDING MEDIA)

Operating Temperature/Humidity		5° to 35°C @ 30 to 80%RH
Storage Temperature/Humidity		-5° to 60°C @ 30 ~ 90%RH, non-condensing (NA for media)

POWER SUPPLY

		100-240 Volts AC +/- 10%, 50/60 Hertz
Input Voltage (AC)		Rated Input voltage: 25 V DC
		Rated current: 1.5 A
Input Voltage (DC)		Rated voltage: 24.0 VDC - 25.25 VDC
Input Voltage (DC)		Rated current: 2 A (Current peak: 13 A)
		Rated current: 2 A (Current peak: 13 A)
Power Consumption		90 Watts (when print ratio is 30%)

PROCESSING

CPU		32 Bit RISC
Flash ROM		4 Megabytes
SDRAM		16 MB

PRINTER LANGUAGE

Standard		SATO Barcode Printer Language (SBPL) 4.3

INTERFACES

Factory-installed only		Bluetooth
Standard configurations		Either 1) USB 2.0 with RS-232C or
Standard configurations		2) USB 2.0 with LAN (10BASE-T/100BASE-TX Automatic Switching)

Optional Interface Board		IEEE1284, 802.11g Wireless Wi-Fi
(user installable)		IEEE1284, 802.11g Wireless Wi-Fi
(user installable)

CT4i Series Operator Manual

2-2

Image 10

Contents Operator Manual Sato America, Inc Table of Contents Cleaning Procedures MaintenanceSato group of Companies Introduction About this Manual Personal InjuryGeneral Description CT4i Series Operator ManualThis page is left blank intentionally Technical Data Environmental Excluding Media Physical CharacteristicsPower Supply ProcessingMedia PrintSensing RibbonMatrix Fonts Character Font CapabilitiesRegulatory Downloadable FontsBarcode Capabilities Interface Specifications Interface SelectionDB25P Signals PIN#Printer Host Specifications PIN Assignments Signal DirectionSoftware Specifications Universal Serial BUS USBLED Indicator Status 802.11G WirelessWireless LAN Signal Strength Socket Connection Diagram Cable Requirements DB9 Host Direction Printer Interface SignalsSignal Signal Definition Receive Buffer ControlCT4i Series Operator Manual CT4i Series Operator Manual This page is intentionally left blank Installation Overview Printer Placement Tips Electrical PrecautionsGeneral Precautions Unpacking & Parts Identification Unpacking & Parts IdentificationMedia Selection Printer InstallationSite Location Media Loading Rolled PaperRibbon Loading Ribbon Take-up SpindleLoading Fanfold Paper Fanfold paper loadingPrinter Label Sensor Positioning Label SensingOperational Mode Selection Label Print Direction This page is intentionally left blank Printer Configuration Configuration Modes Operating PanelRear Panel Fanfold-label Loading SlotDIP Switch Settings Configuration PanelLED Switch 4 DT/TT Mode DIP Switch Settings CONT’DSwitch 5 Head Check Switch 7 Data Dump Switch 6 VR1 Potentiometer Adjustment modeSwitch 8 Interface Board selection Power on sequence for various Operational Modes Operational ModesNormal Mode LED and Buzzer status during Normal Mode operationOperational Modes CONT’D Data found on Test Prints User Test Print Mode Feed + Power onData Printed Parameter Default Setting Default Settings Mode Online + Feed + Power onHEX Dump Mode Power on with DSW7=ON Settings AffectedDSW5 DSW6 DSW8 Font Download Mode DSW1=OFF, DSW2=ON, DSW3=ON + Power on Online Error Buzzer LEDProgram Download Mode DSW1=ON, DSW2=OFF, DSW3=ON + Power on FunctionErrors during Font and Program Download Modes CauseMode Length of Offset mm Print head resolution OffsetsOriginal First Line Print Position Potentiometer AdjustmentsPitch Offset Moved with Leading Edge Positive + OffsetPotentiometer Adjustments CONT’D Print DarknessData Dump Diagnostic Label Printing Test Labels Printing FACTORY/SERVICE Test Prints CT4i Series Operator Manual Troubleshooting Troubleshooting Guide ErrorBlinks Light Print Images Image VoidsRibbon Wrinkling Uneven Print DarknessIncorrect Label Positioning No Printed ImagePrinter Creates a Blank Label Smeared Print ImagesInterface Troubleshooting CHK Troubleshooting StepLAN Ethernet Interface HEX Dump Test Print TroubleshootingTest Label Printing Maintenance Cleaning Procedures Print Head ReplacementAdjusting the Print Quality Adjustment ProceduresPrint Speed Cleaning the Print Head Cleaning the Print HEAD, Platen and RollersClearning Stubborn Debris on the Print Head Cleaning the Print HEAD, Platen and Rollers CONT’D Cleaning the Platen and Paper RollerRELEASING/REPLACING the Print Head Cleaning the Sensor CT4i Series Operator Manual Sato Group of Companies Sato Group of Companies Asia Pacific & Oceania Region