SATO ct4i manual Configuration Modes, Operating Panel

Page 38

Unit 4: Printer Configuration

CONFIGURATION MODES

Before using the printer, read this manual thoroughly first. Otherwise, you may disturb default settings upon which the instructional procedures in this manual are based. The printer may be configured via the buttons and/or potentiometers located on the printer’s front panel. All of the printer’s buttons, switches, and potentiometers are used either singularly, or in conjunction, to perform configuration activities.

4.1 OPERATING PANEL

The Operator Panel consists of three LED indicators and three switches.

POWER

The green LED lights up when the printer is ON.

ERROR

The red LED lights up when there is a system fault such as an unlatched print head.

ON LINE

The green LED lights up when the printer is ON LINE and ready to receive data. The ON LINE button takes the printer ON LINE or OFF LINE.

ON LINE Button

If the ONLINE LED is lit, pressing it will take the printer OFF LINE. Pressing the button again then takes the printer back ON LINE. When ON LINE, the printer is ready to receive data from the host. When OFF LINE, the printer will not print or accept data from the host. While the printer is printing, press this button to suspend the printing. To resume printing, press this button again.

FEED BUTTON

Press this button to eject one label in OFF LINE mode.

Hold this button down while power is applied, to print a printer status label.

POWER SWITCH

A two position switch for turning the printer ON (I) or OFF (0).

CT4i Series Operator Manual

4-2

Image 38
Contents Operator Manual Sato America, Inc Table of Contents Sato group of Companies MaintenanceCleaning Procedures Introduction About this Manual Personal InjuryGeneral Description CT4i Series Operator ManualThis page is left blank intentionally Technical Data Environmental Excluding Media Physical CharacteristicsPower Supply ProcessingMedia PrintSensing RibbonMatrix Fonts Character Font CapabilitiesRegulatory Downloadable FontsBarcode Capabilities Interface Specifications Interface SelectionPrinter Host Signals PIN#DB25P Specifications PIN Assignments Signal DirectionSoftware Specifications Universal Serial BUS USBLED Indicator Status 802.11G WirelessWireless LAN Signal Strength Socket Connection Diagram Cable Requirements DB9 Host Direction Printer Interface SignalsSignal Signal Definition Receive Buffer ControlCT4i Series Operator Manual CT4i Series Operator Manual This page is intentionally left blank Installation Overview Printer Placement Tips Electrical PrecautionsGeneral Precautions Unpacking & Parts Identification Unpacking & Parts IdentificationMedia Selection Printer InstallationSite Location Media Loading Rolled PaperRibbon Loading Ribbon Take-up SpindleLoading Fanfold Paper Fanfold paper loadingPrinter Label Sensor Positioning Label SensingOperational Mode Selection Label Print Direction This page is intentionally left blank Printer Configuration Configuration Modes Operating PanelRear Panel Fanfold-label Loading SlotLED Configuration PanelDIP Switch Settings Switch 5 Head Check DIP Switch Settings CONT’DSwitch 4 DT/TT Mode Switch 8 Interface Board selection Switch 6 VR1 Potentiometer Adjustment modeSwitch 7 Data Dump Power on sequence for various Operational Modes Operational ModesOperational Modes CONT’D LED and Buzzer status during Normal Mode operationNormal Mode Data Printed User Test Print Mode Feed + Power onData found on Test Prints Parameter Default Setting Default Settings Mode Online + Feed + Power onDSW5 DSW6 DSW8 Settings AffectedHEX Dump Mode Power on with DSW7=ON Font Download Mode DSW1=OFF, DSW2=ON, DSW3=ON + Power on Online Error Buzzer LEDProgram Download Mode DSW1=ON, DSW2=OFF, DSW3=ON + Power on FunctionErrors during Font and Program Download Modes CauseMode Length of Offset mm Print head resolution OffsetsOriginal First Line Print Position Potentiometer AdjustmentsPitch Offset Moved with Leading Edge Positive + OffsetPotentiometer Adjustments CONT’D Print DarknessData Dump Diagnostic Label Printing Test Labels Printing FACTORY/SERVICE Test Prints CT4i Series Operator Manual Troubleshooting Troubleshooting Guide ErrorBlinks Light Print Images Image VoidsRibbon Wrinkling Uneven Print DarknessIncorrect Label Positioning No Printed ImagePrinter Creates a Blank Label Smeared Print ImagesInterface Troubleshooting CHK Troubleshooting StepLAN Ethernet Interface Test Label Printing Test Print TroubleshootingHEX Dump Maintenance Cleaning Procedures Print Head ReplacementPrint Speed Adjustment ProceduresAdjusting the Print Quality Clearning Stubborn Debris on the Print Head Cleaning the Print HEAD, Platen and RollersCleaning the Print Head Cleaning the Print HEAD, Platen and Rollers CONT’D Cleaning the Platen and Paper RollerRELEASING/REPLACING the Print Head Cleaning the Sensor CT4i Series Operator Manual Sato Group of Companies Sato Group of Companies Asia Pacific & Oceania Region