Nortel Networks 1002rp manual To set the modem DIP switches, Off

Page 63

October 2006

Installing the server and connecting the peripheral devices

To set the modem DIP switches

Use a pair of tweezers or a small screwdriver to set the DIP switches as described in the Change to column of the following table:

Note: ON is down. OFF is up.

DIP

Default

Change

 

 

switch

setting

to

Function

 

 

 

 

1

OFF

OFF

Data Terminal Ready (DTR) override

 

 

 

„

OFF: Normal DTR operations. (The

 

 

 

 

computer must provide a DTR signal for the

 

 

 

 

modem to accept commands. If DTR is

 

 

 

 

dropped, the call is terminated.)

 

 

 

„

ON: The modem ignores DTR (override).

 

 

 

 

2

OFF

OFF

Verbal/numeric result codes

 

 

 

„

OFF: Verbal (word) results.

 

 

 

„

ON: Numeric results.

 

 

 

 

3

ON

ON

Result code display

 

 

 

„

OFF: Suppresses result codes.

 

 

 

„

ON: Enables result codes.

 

 

 

 

4

OFF

OFF

Command mode local echo suppression

 

 

 

„

OFF: Displays keyboard commands.

 

 

 

„

ON: Suppresses echo.

 

 

 

 

5

ON

ON

Auto answer suppression

 

 

 

„

OFF: The modem answers on the first ring,

 

 

 

 

or higher if specified in NVRAM.

 

 

 

„

ON: Disables auto answer.

1002rp Server Hardware Installation

63

Image 63
Contents 1002rp Server Hardware Installation Copyright 2006 Nortel Networks 1002rp Server Hardware Installation Information for Japan があります。この場合には使用者が適切な対策を取るように要求されることがあ ります。 Standard Publication history Publication history To connect the mouse, keyboard, and monitor to the server Task ListTask List Contents EMC emission level protection for the 1002rp Server Index Getting Help from the Nortel Web site How to get HelpGetting Help over the phone from a Nortel Solutions Center A p t e rGetting Help through a Nortel distributor or reseller This chapter 1002rp server descriptionServer features Server dimensions and weightIntroduction Environmental specifications Alarm board Front panel features front view without the front bezelRear panel diagram Overhead view of empty server showing PCI and ISA connectors Slot definition and slot numbering Slot assignments1002rp slot assignments BRD13 1002rp server description Network connectivity Sample network setup Meridian CE-MUX Sample network setup SuccessionCallPilot Elan and Clan network setup Switch connectivityNetwork requirements Remote access connectivityModem Kbit/s external modem NTRH9078 provides Supported peripheral devicesCallPilot Customer Documentation Map Reference documents1002rp server description Preparing for installation Installation checklist Installation overviewOctober 2006Preparing for installation Conventions for warnings To unpack the equipment Unpacking the 1002rp serverWhat’s next? Removing the front bezel and server cover To remove the front bezel To remove the server cover To inspect the server interior Inspecting the server interiorOctober To replace the front bezel after installation is complete Power supply installation Safety precautions Safety informationEquipment handling guidelines Installing the second power supply module AC or DC About the power supply moduleAC versus DC systems Power supply modules To install the power supply module DC wire gauge tables Metric wire conversion DC rack cabling Rack power and grounding DC power distribution rationale About the power distribution unit PDU power and groundingMultiple PDUs DC power input PDU terminal blocks and wiring diagramTo bring DC power and ground into the PDU Bringing power and ground into the PDUPower supply installation Installing the server and connecting the peripheral devices To install the server Installing the serverRequired equipment Preparing the modemDIP Modem DIP switchesOFF To set the modem DIP switchesCarrier Detect CD override Rear panel connectors Connecting peripherals to the serverTo connect the modem to the server To connect the mouse, keyboard, and monitor to the serverContinue with Connecting the server to the Elan on Connecting the server to the Elan Media Access Control addressTo connect the server to the Elan 555-7101-210 If the server will To connect the server to the Clan Connecting the server to the Clan optionalInstalling the server and connecting the peripheral devices Installing the Nortel software feature dongle Requirements To install the software feature dongleBefore you begin Connecting the server to powerCallPilot Server To connect the 1002rp DC server to power To connect the 1002rp AC server to powerTo start the server P e n d i x a EMC emission level protection for the 1002rp ServerFerrites secured to an external cable Numerics IndexIndex October Index Index Page 1002rp Server Hardware Installation