American Power Conversion AIS 5000 manual Access to Input/Output section

Page 21

External Connection - Connecting the UPS

5.Install Conduit Box under UPS. Push projecting edge of Conduit Box into slot on UPS bottom plate. From inside the UPS, mount front of Conduit Box onto UPS bottom plate using 2 M4×12 cross head screws for 10–30 kVA and 3 M4×12 cross head screws for 40–100 kVA.

6.Mount conduits.

7.Feed cables.

8.Install cables according to the procedures described in the following sections.

Access to Input/Output section

To access cable terminals, open front door, remove screws and lift off front cover (remember earth wire on rear side).

Remember to remount front cover (and earth wire) before system start-up.

CAUTION!

Ensure correct phase rotation of utility input voltage! Max. power cable size: see section Caution with technical specifications starting on page 24.

990-2440

AIS 5000 400V Installation Manual

15

Image 21

Contents AIS Page Contents Options Operation Modes Page Symbols used in this manual SafetyDisconnect all sources of AC and DC power User SafetyAbout this manual General InformationReceiving and inspecting the UPS Site RequirementsMoving the equipment to site Fitting the air filter Air FilterAir filter sizes Enclosure dimensions Enclosure dimensions and footprintTop and bottom view of 10-30kVA UPS Top and bottom view of 40-60kVA UPS Top and bottom view of 80-100kVA UPS External connection board Connecting the UPS UPS Feet  Conduit Box  Front of Conduit Box Installing Conduit BoxesInput Conduit Output/Bypass Battery Alarm Conduit Access to Input/Output section Low-voltage section cover Communication Interface, EPO Connecting cables Input/Output -60 kVA Input/Output -100 kVA X090 GroundingCommunication interface Emergency Power Off EPOCOM-PORT Communication interface portsOverview of Communication interface COM Interface10kVA 400V UPS Max. Discharge Current a 46 a Nominal Voltage 240Approvals IEC 62040/EN 50091 Class A, VFI-SS-112 Emergency Power Off EPO YesOptions Voltage 400 V 3 Wire + N + G Nominal Current 28.9 a Mains Voltage 400 V 3 Wire + G Nom 19.88 kW 33.79 a20kVA 400V UPS Max 39.4 aMax. Discharge Current a 91 a External Connection 20kVA 400V UPS Options Voltage 400 V 3 Wire + N + G Nominal current 43.3 a Mains Voltage 400 V 3 Wire + G Nom 28.35 kW 47.86 a30kVA 400V UPS Max 59.9 aMax. Discharge Current a 135 a External Connection 30kVA 400V UPS Options Voltage 400 V 3 Wire + N + G Nominal current 57.7 a Mains Voltage 400 V 3 Wire + G Nom 36.9 kW 61.93 a40kVA 400V UPS Max 77.8 aMax. Discharge Current a 179 External Connection 40kVA 400V UPS Options Voltage 400 V 3 Wire + N + G Nominal current 86.6 a Mains Voltage 400 V 3 Wire + G Nom 54.42 kW 90.08 a60kVA 400V UPS Max 117 aMax. Discharge Current a 266 External Connection 60kVA 400V UPS Options Voltage 400 V 3 Wire + N + G Nominal current 115.5 a Mains Voltage 400 V 3 Wire + G Nom 72.33 kW 118.23 a80kVA 400V UPS Max 152.8 aMax. Discharge Current a 353 External Connection 80kVA 400V UPS Options 100kVA 400V UPS Max. Discharge Current a 442 External Connection 100kVA 400V UPS Options Options IP32 Drip Shield Mounting the drip shield Drip shield sizes Message Relay BoardMessage Cards and slots Communication CardsDisplay introduction DisplayDisplay functions Display messages Programming the UPS User stackKeys Until the display shows Bypass Operation Push Cursor keys Programming and Set-Up Programming the UPSAuto Boost Charge OFF Battery Capacity Test ??? Battery Monitor Alarm Settings for redundant systems Enter new time HH.MM.SS Setting stack Minutes10 kVA 20 kVA 30 kVA 40 kVA 60 kVA 80 kVA 100 kVA How to change factory settings Operation Modes Operation mode descriptionsNormal to Bypass Operation Bypass to Normal OperationPress Normal to Manual Bypass Operation Load is now supported by the UPS Page 990-2440