American Power Conversion AIS 5000 manual COM Interface, Overview of Communication interface

Page 29

External Connection - Connecting the UPS

Overview of Communication interface

COM INTERFACE

X003 25 pin SUB-D male

X004 25 pin SUB-D male

X005 25 pin SUB-D female

X005X004X003

MULTICOM,

Serial Port: RS 232, V24

(normally used for optional smartslot)

Serial Port: 0 to 20mA current loop

COM PORT

	C 14	NC1
	C 15	NO1
	C 15	NO1
	C 2	COM1
	C 16	NC2
	C 17	NO2
	C 17	NO2
	C 4	COM2
	C 18	NC3
	C 19	NO3
	C 19	NO3
	C 6	COM3
	C 20	NC4
	C 21	NO4
	C 21	NO4
C 8		COM4

"OFF" (2 - 14) "ON" (2 - 15)

	"Normal Operation" (4-16)	Relay Contacts
	"Bypass Operation" (4-17)	Relay Contacts
	"Bypass Operation" (4-17)

"Normal Operation" (6-18)

"Battery Operation" (6-19)

"Battery Voltage OK" (8-20)

"Battery Voltage Low" (8-21)

	C 13	+	Remote UPS shut down input

	C 25	-	3,5 to 25V pulse IN at min. 1 sec.

990-2440

AIS 5000 400V Installation Manual

23

Image 29

Contents AIS Page Contents Options Operation Modes Page Symbols used in this manual SafetyDisconnect all sources of AC and DC power User SafetyAbout this manual General InformationReceiving and inspecting the UPS Site RequirementsMoving the equipment to site Fitting the air filter Air FilterAir filter sizes Enclosure dimensions Enclosure dimensions and footprintTop and bottom view of 10-30kVA UPS Top and bottom view of 40-60kVA UPS Top and bottom view of 80-100kVA UPS External connection board Connecting the UPS UPS Feet  Conduit Box  Front of Conduit Box Installing Conduit BoxesInput Conduit Output/Bypass Battery Alarm Conduit Access to Input/Output section Low-voltage section cover Communication Interface, EPO Connecting cables Input/Output -60 kVA Input/Output -100 kVA X090 GroundingCommunication interface Emergency Power Off EPOCOM-PORT Communication interface portsOverview of Communication interface COM Interface10kVA 400V UPS Max. Discharge Current a 46 a Nominal Voltage 240Approvals IEC 62040/EN 50091 Class A, VFI-SS-112 Emergency Power Off EPO YesOptions Voltage 400 V 3 Wire + N + G Nominal Current 28.9 a Mains Voltage 400 V 3 Wire + G Nom 19.88 kW 33.79 a20kVA 400V UPS Max 39.4 aMax. Discharge Current a 91 a External Connection 20kVA 400V UPS Options Voltage 400 V 3 Wire + N + G Nominal current 43.3 a Mains Voltage 400 V 3 Wire + G Nom 28.35 kW 47.86 a30kVA 400V UPS Max 59.9 aMax. Discharge Current a 135 a External Connection 30kVA 400V UPS Options Voltage 400 V 3 Wire + N + G Nominal current 57.7 a Mains Voltage 400 V 3 Wire + G Nom 36.9 kW 61.93 a40kVA 400V UPS Max 77.8 aMax. Discharge Current a 179 External Connection 40kVA 400V UPS Options Voltage 400 V 3 Wire + N + G Nominal current 86.6 a Mains Voltage 400 V 3 Wire + G Nom 54.42 kW 90.08 a60kVA 400V UPS Max 117 aMax. Discharge Current a 266 External Connection 60kVA 400V UPS Options Voltage 400 V 3 Wire + N + G Nominal current 115.5 a Mains Voltage 400 V 3 Wire + G Nom 72.33 kW 118.23 a80kVA 400V UPS Max 152.8 aMax. Discharge Current a 353 External Connection 80kVA 400V UPS Options 100kVA 400V UPS Max. Discharge Current a 442 External Connection 100kVA 400V UPS Options Options IP32 Drip Shield Mounting the drip shield Drip shield sizes Message Relay BoardMessage Cards and slots Communication CardsDisplay introduction DisplayDisplay functions Display messages Keys Until the display shows Programming the UPSUser stack Bypass Operation Push Cursor keys Programming and Set-Up Programming the UPSAuto Boost Charge OFF Battery Capacity Test ??? Battery Monitor Alarm Settings for redundant systems Enter new time HH.MM.SS 10 kVA 20 kVA 30 kVA 40 kVA 60 kVA 80 kVA 100 kVA Setting stackMinutes How to change factory settings Operation Modes Operation mode descriptionsPress Normal to Bypass OperationBypass to Normal Operation Normal to Manual Bypass Operation Load is now supported by the UPS Page 990-2440