American Power Conversion AIS 5000 manual Message

Page 63

Options - Relay Board

Message:

Output Static Switch Inhibited

Bypass Static Switch Inhibited

Asynchronous

Overload Inv/Bypass

Inverter Fault

Battery Operation

Rectifier Failure

EN ON

EA ON

Inverter ON

Boost Charge ON

Charger ON

External Horn

Relay #

X001		2,5
	011
	012
	013
X002	013	2,5
X002		2,5
	021
	022
	024
X003	024	2,5

	031
	031
	032
X004	034
	034	2,5
		2,5
	041
	042
	042
	044
X005	044	2,5
X005		2,5
	051
	052
	054
X006	054	2,5
X006		2,5
	061
	062
	064
X007	064	2,5
		2,5
	071
	071
	072
X008	074
	074	2,5
		2,5
	081
	082
	084
X009	084	2,5
X009		2,5
	091
	092
	094
X010	094	2,5
X010		2,5
	101
	102
	104
X011	104	2,5
X011		2,5
	111
	112
	114
X012	114	2,5
X012		2,5
	121
	122
	124
X013	124	2,5
X013		2,5
	131
	132
	134
X014	134	2,5
X014		2,5
	141
	142
	144
X015	144	2,5
X015		2,5
	151
	152
X016	154
	154	2,5
		2,5
	161
	162
	164
	164

* * * * * * * * *

K001	A078	LOW-VOLTAGE
K002 K003		SECTION
K004
K005
K006
K007
K008
K009
K010
K011
K012		STATUS
K013		STATUS
K014		POSITION
K015 K016		* ALARM POSITION

990-2440

AIS 5000 400V Installation Manual

57

Image 63

Contents AIS Page Contents Options Operation Modes Page Symbols used in this manual SafetyDisconnect all sources of AC and DC power User SafetyAbout this manual General InformationReceiving and inspecting the UPS Site RequirementsMoving the equipment to site Fitting the air filter Air FilterAir filter sizes Enclosure dimensions Enclosure dimensions and footprintTop and bottom view of 10-30kVA UPS Top and bottom view of 40-60kVA UPS Top and bottom view of 80-100kVA UPS External connection board Connecting the UPS UPS Feet  Conduit Box  Front of Conduit Box Installing Conduit BoxesInput Conduit Output/Bypass Battery Alarm Conduit Access to Input/Output section Low-voltage section cover Communication Interface, EPO Connecting cables Input/Output -60 kVA Input/Output -100 kVA X090 GroundingCommunication interface Emergency Power Off EPOCOM-PORT Communication interface portsOverview of Communication interface COM Interface10kVA 400V UPS Max. Discharge Current a 46 a Nominal Voltage 240Approvals IEC 62040/EN 50091 Class A, VFI-SS-112 Emergency Power Off EPO YesOptions Max 39.4 a Mains Voltage 400 V 3 Wire + G Nom 19.88 kW 33.79 aVoltage 400 V 3 Wire + N + G Nominal Current 28.9 a 20kVA 400V UPSMax. Discharge Current a 91 a External Connection 20kVA 400V UPS Options Max 59.9 a Mains Voltage 400 V 3 Wire + G Nom 28.35 kW 47.86 aVoltage 400 V 3 Wire + N + G Nominal current 43.3 a 30kVA 400V UPSMax. Discharge Current a 135 a External Connection 30kVA 400V UPS Options Max 77.8 a Mains Voltage 400 V 3 Wire + G Nom 36.9 kW 61.93 aVoltage 400 V 3 Wire + N + G Nominal current 57.7 a 40kVA 400V UPSMax. Discharge Current a 179 External Connection 40kVA 400V UPS Options Max 117 a Mains Voltage 400 V 3 Wire + G Nom 54.42 kW 90.08 aVoltage 400 V 3 Wire + N + G Nominal current 86.6 a 60kVA 400V UPSMax. Discharge Current a 266 External Connection 60kVA 400V UPS Options Max 152.8 a Mains Voltage 400 V 3 Wire + G Nom 72.33 kW 118.23 aVoltage 400 V 3 Wire + N + G Nominal current 115.5 a 80kVA 400V UPSMax. Discharge Current a 353 External Connection 80kVA 400V UPS Options 100kVA 400V UPS Max. Discharge Current a 442 External Connection 100kVA 400V UPS Options Options IP32 Drip Shield Mounting the drip shield Drip shield sizes Message Relay BoardMessage Cards and slots Communication CardsDisplay introduction DisplayDisplay functions Display messages Programming the UPS User stackKeys Until the display shows Bypass Operation Push Cursor keys Programming and Set-Up Programming the UPSAuto Boost Charge OFF Battery Capacity Test ??? Battery Monitor Alarm Settings for redundant systems Enter new time HH.MM.SS Setting stack Minutes10 kVA 20 kVA 30 kVA 40 kVA 60 kVA 80 kVA 100 kVA How to change factory settings Operation Modes Operation mode descriptionsNormal to Bypass Operation Bypass to Normal OperationPress Normal to Manual Bypass Operation Load is now supported by the UPS Page 990-2440