Epson 60 manual Operation Panel, Buttons

Page 11

OPERATION PANEL

BUTTONS

To operate the printer, you will use the four buttons marked , , , and . These keys are only for use with the printer (that is, they do not operate as cursor keys when inputting telephone numbers). See your fax machine’s Operator’s Manual to see where these are on your fax machine.

The main uses of these four printer mode buttons are as follows.

Press this to enter printer setup mode from printer "Ready" mode. Set up mode is also known as Selectype mode. Also, when in printer setup mode, press this repeatedly to return to printer "Ready" mode.

This button has three main functions:

❐If the (Line Fail) indicator is flashing, read the error message on the display and correct the problem (see page 44 for details). Then, press this button to resu me printing.

❐If you hold this button down for several seconds, RESET appears on the display and all printer settings are returned to their previously stored settings. If you continue to press this button after RESET appears, INITIALIZE will appear on the display, and the printer settings will return to the power-on default settings. For more on resetting the machine, see page 15.

❐If you switch the printer off line then press this button during a multi-copy print run, any remaining copies will be canceled.

When the printer is off line and the (Feed) indicator is lit, press this button to print out the data remaining in the printer’s memory. If you are using more than one channel, you can print data received by each channel alternately. See Form Feed on page 14. (As a reminder, note that this arrow key points towards the printout tray.)

Watch the (on line/off line) indicator, and press this button to switch the printer be - tween on line and off line modes. Do this only when the machine is in printer "Ready" mode. (As a reminder, note that the arrow on the arrow key points the same way as the arrow in the On Line indicator.)

5

Image 11

Contents Printer Interface Type OPERATOR’S Manual Page Contents Test Print Mode Assign Selectype Level 1 FeaturesSave Macro Load Macro Poweron Macro Delete Macro Selectype Level 2 FeaturesAvailable Fonts and Symbol Sets Table of SpecificationsHP Emulation Mode VS HP Laserjet Using Selectype Mode to Adjust the HP Emulation ModeOperating AS AN LQ or FX Printer Using Selectype Mode to Adjust Epson LQ and FX EmulationLQ and FX Emulation Command Summary Font Cards and Emulation Mode CardsAbout the Printer Interface IntroductionIntroduction Conventions About this Manual Buttons Operation PanelDisplay IndicatorsConnection to the Computer InstallationInstalling the Interface KIT Printing a Test Testing the PrinterFor full information about macros See pages 31 to Memory Expansion Board Optional KitsOptional Font and Emulation Mode Cards Optional Font Cartridges Multi-user Modes Connecting the Printer to TWO ComputersForm Feed Basic OperationsTurning the Printer on Line and OFF Line Selecting the Cassette for Computer Printing Resetting the PrinterOverview Selecting the Emulation ModeHP Laserjet III Emulation Mode Epson LQ and FX Emulation Modes Changing the Emulation ModeUsing the Mode Assign Feature Epson Job Language EJL Using an Emulation Control LanguageClose ESC SOH@EJL Enter LANGUAGE=LJ-3REM Copy HP.TXT LPT1 EitherPrinter Job Language Introduction Adjusting the Printer SettingsLevel 2 Features Using Selectype Mode Display Sample Selectype Procedure Display the required setting for this feature Selectype Level 1 Features Available Options 1 to InputSize CopiesStatus Sheet SUB ConfigOrient FontFull Print System ConfigOffset and L-OFFSET Paper Size SettingMemory Left Save Macro Load Macro Delete Macro Poweron MacroTest Print Selectype Level 2 FeaturesHow to Enter Selectype Level Mode AssignAvailable Options ON, OFF CONFIG. Interface ConfigurationParallel Channel Available Options 1 or Serial ChannelAvailable Options 8-bit or 7-bit RX-BUFFER Size Receive Buffer Size CH Channel If you selected Individual If you selected AutosenseCH Timeout Channel Timeout Auto Cont Auto Continue Config Save Power-up ConfigurationVersion Factory ResetStandby CounterChar Creating Solving ProblemsStatus and Error Messages Change PCUInitialize Feed JAMFont Creating Graphic DrawingRemove Card Paper Size ErrorPrinting Reinsert CardToner OUT Startup ErrorSET Full Print Toner LOWPaper OUT or Toner OUT is displayed Printing ProblemsOn-line/off-line indicator is off Some or all of the output is garbled or printed as asterisks You cannot print graphics using the serial channel Problems with GraphicsDesired Selectype settings are not displayed Problems with Selectype ModeProblems with Optional Cards and Cartridges Data Dump Mode ESC R Appendix A. Specifications Printable Area Appendix B. HP Emulation ModeHP Emulation Modevs HP Laserjet Downloaded Fonts Fonts Font name in HP emulation modeCharacter Clipping Paper HandlingEsc # Esc s#P Esc s#B Esc s#S Esc s#T Symbol SetsOperating AS a Laserjet IIISi Orient Page Orientation Using Selectype Mode to Adjust the HP Emulation ModeAppendix B. HP Emulation Mode Available Options 0 to Resident Bitmap Fonts Available Fonts and Symbol SetsFont Name Spacing Height Typeface Style Weight Attribute Bitmap ScalableResident Scalable Fonts Font Name Symbol Set Height pt Typeface Style WeightAppendix B. HP Emulation Mode IBM-US 10U IBM-DN 11U PcMultilingual 12U Legal 1U ISO Ansi Ascii 0U Ventura International 13J Ventura US 14J PS Math 5M PS Text 10J Math-8 8M Pi Font 15U Microsoft Publishing 6J Windows 9U Desktop 7J Ve Zapf Dingbats 9L Ps Zapf Dingbats 10L Zd 100 11L Zd 200 12L Zd 300 13L HP Emulation Command Summary Font selection Printer commands arranged by topicControl codes OrientationESC0L ESC2KESC8K ESC9KOffset Length, page size, text lengthMargins Specialized printer control Perforation skip modeVertical line spacing Half-line feedRaster graphics Font managementMacros Push/Pop positionVector group GL/2 mode Configuration and status groupVector graphics Line and fill attributes groupPaper Size Appendix C. Epson LQ and FX Emulation ModesOperating AS AN LQ or FX Printer Using Selectype to Adjust Epson LQ and FX Emulation Paper Size Condensed Portrait Landscape 10 cpi 12 cpi 15 cpi Appendix C. Epson LQ and FX Emulation Modes Appendix C. Epson LQ and FX Emulation Modes Character Sets Font Name Pitch cpi OrientationPc USA Epson International Character Sets SI/ESC SI LQ and FX Emulation Command SummaryESC U ESC G/ESC EESC EM DELCan Vertical motion Printer operationData control Print size and character width Horizontal motionPrint position Overall printing styleUser-defined characters Word processingESC SP Character tablesFont Cards Font Cards and Emulation Mode CardsEmulation Mode Cards Appendix D. Optional Font Cards and CartridgesCaring for Cards Selecting a font with the Selectype Font procedureUsing the Epson GL Emulation Mode Card When the printer is in 3/P/Si modeWhen the printer is in LQ or FX mode Using a font card and a font cartridge at the same timeAvailable Font Cartridges Recovering from a Card ErrorFont Cartridges Maker Cartridge Number Recovering from a cartridge error Level Appendix E. List of FeaturesTest Print JIS ASC Si Emulation ModeEpson LQ or FX Emulation Mode Serial Interface Pin Number Signal Name Appendix F. Connector PIN ConfigurationParallel Interface Pin Number Signal Name Pin assignments for typical ATs and compatibles Following is an example of a status sheet printout Appendix G. Status Sheet