Epson 60 manual Printing the Status Sheet and Font Samples

Page 15

INSTALLATION

Printing the Status Sheet and Font Samples

1.

Function 3 5 Yes

2.Press until the screen is as shown on the right, then release it immediately.

3.Hold down until STATUS SHEET (or FONT SAMPLE if you need the font sam - ples) appears on the display.

4.Press twice to print the status sheet (or the font samples). The printer may take a few seconds to get started on this.

5.Press twice to return to printer "Ready" mode.

6. Press

Function

to leave printer mode.

Note: ❐ The status sheet shows the printer’s current settings. You can use macros to store various sets of printer settings for different uses of the printer. If you wish to print the settings stored with each macro, perform the LOAD MACRO routine first, then follow the above steps.

For full information about macros: See pages 31 to 33 .

❐If you have already set the printer up in Individual Multi-user mode: The following display appears at step 2.

Press to select the serial (S) channel, or to choose the parallel (P) channel, then go on to step 3.

❐If you have already set the printer up in Autosense Multi-user mode: You can only print out the status sheet or font samples for the channel that was displayed on the screen immediately before you started this procedure. If you wish to see the settings for the other channel, you will have to select the other channel using the CH feature (for example, change from AUTO - SENSE S to AUTOSENSE P). Then print the status sheet or font samples. For information on the CH feature, see page 38.

❐A sample of the status sheet is shown in Appendix G.

9

Image 15

Contents Printer Interface Type OPERATOR’S Manual Page Contents Test Print Mode Assign Selectype Level 1 FeaturesSave Macro Load Macro Poweron Macro Delete Macro Selectype Level 2 FeaturesAvailable Fonts and Symbol Sets Table of SpecificationsHP Emulation Mode VS HP Laserjet Using Selectype Mode to Adjust the HP Emulation ModeOperating AS AN LQ or FX Printer Using Selectype Mode to Adjust Epson LQ and FX EmulationLQ and FX Emulation Command Summary Font Cards and Emulation Mode CardsAbout the Printer Interface IntroductionIntroduction Conventions About this Manual Buttons Operation PanelDisplay IndicatorsInstallation Installing the Interface KITConnection to the Computer Printing a Test Testing the PrinterFor full information about macros See pages 31 to Memory Expansion Board Optional KitsOptional Font and Emulation Mode Cards Optional Font Cartridges Multi-user Modes Connecting the Printer to TWO ComputersBasic Operations Turning the Printer on Line and OFF LineForm Feed Selecting the Cassette for Computer Printing Resetting the PrinterSelecting the Emulation Mode HP Laserjet III Emulation ModeOverview Changing the Emulation Mode Using the Mode Assign FeatureEpson LQ and FX Emulation Modes Epson Job Language EJL Using an Emulation Control LanguageClose ESC SOH@EJL Enter LANGUAGE=LJ-3REM Copy HP.TXT LPT1 EitherPrinter Job Language Introduction Adjusting the Printer SettingsLevel 2 Features Using Selectype Mode Display Sample Selectype Procedure Display the required setting for this feature Selectype Level 1 Features Available Options 1 to InputSize CopiesStatus Sheet SUB ConfigOrient FontFull Print System ConfigPaper Size Setting Memory LeftOffset and L-OFFSET Save Macro Load Macro Delete Macro Poweron MacroTest Print Selectype Level 2 FeaturesHow to Enter Selectype Level Mode AssignCONFIG. Interface Configuration Parallel ChannelAvailable Options ON, OFF Serial Channel Available Options 8-bit or 7-bitAvailable Options 1 or RX-BUFFER Size Receive Buffer Size CH Channel If you selected Individual If you selected AutosenseCH Timeout Channel Timeout Auto Cont Auto Continue Config Save Power-up ConfigurationVersion Factory ResetStandby CounterChar Creating Solving ProblemsStatus and Error Messages Change PCUInitialize Feed JAMFont Creating Graphic DrawingRemove Card Paper Size ErrorPrinting Reinsert CardToner OUT Startup ErrorSET Full Print Toner LOWPrinting Problems On-line/off-line indicator is offPaper OUT or Toner OUT is displayed Some or all of the output is garbled or printed as asterisks You cannot print graphics using the serial channel Problems with GraphicsDesired Selectype settings are not displayed Problems with Selectype ModeProblems with Optional Cards and Cartridges Data Dump Mode ESC R Appendix A. Specifications Appendix B. HP Emulation Mode HP Emulation Modevs HP LaserjetPrintable Area Downloaded Fonts Fonts Font name in HP emulation modeCharacter Clipping Paper HandlingEsc # Esc s#P Esc s#B Esc s#S Esc s#T Symbol SetsOperating AS a Laserjet IIISi Orient Page Orientation Using Selectype Mode to Adjust the HP Emulation ModeAppendix B. HP Emulation Mode Available Options 0 to Resident Bitmap Fonts Available Fonts and Symbol SetsFont Name Spacing Height Typeface Style Weight Attribute Bitmap ScalableResident Scalable Fonts Font Name Symbol Set Height pt Typeface Style WeightAppendix B. HP Emulation Mode IBM-US 10U IBM-DN 11U PcMultilingual 12U Legal 1U ISO Ansi Ascii 0U Ventura International 13J Ventura US 14J PS Math 5M PS Text 10J Math-8 8M Pi Font 15U Microsoft Publishing 6J Windows 9U Desktop 7J Ve Zapf Dingbats 9L Ps Zapf Dingbats 10L Zd 100 11L Zd 200 12L Zd 300 13L HP Emulation Command Summary Font selection Printer commands arranged by topicControl codes OrientationESC0L ESC2KESC8K ESC9KLength, page size, text length MarginsOffset Specialized printer control Perforation skip modeVertical line spacing Half-line feedRaster graphics Font managementMacros Push/Pop positionVector group GL/2 mode Configuration and status groupVector graphics Line and fill attributes groupAppendix C. Epson LQ and FX Emulation Modes Operating AS AN LQ or FX PrinterPaper Size Using Selectype to Adjust Epson LQ and FX Emulation Paper Size Condensed Portrait Landscape 10 cpi 12 cpi 15 cpi Appendix C. Epson LQ and FX Emulation Modes Appendix C. Epson LQ and FX Emulation Modes Character Sets Font Name Pitch cpi OrientationPc USA Epson International Character Sets SI/ESC SI LQ and FX Emulation Command SummaryESC U ESC G/ESC EDEL CanESC EM Printer operation Data controlVertical motion Print size and character width Horizontal motionPrint position Overall printing styleUser-defined characters Word processingESC SP Character tablesFont Cards Font Cards and Emulation Mode CardsEmulation Mode Cards Appendix D. Optional Font Cards and CartridgesCaring for Cards Selecting a font with the Selectype Font procedureUsing the Epson GL Emulation Mode Card When the printer is in 3/P/Si modeWhen the printer is in LQ or FX mode Using a font card and a font cartridge at the same timeRecovering from a Card Error Font CartridgesAvailable Font Cartridges Maker Cartridge Number Recovering from a cartridge error Level Appendix E. List of FeaturesTest Print JIS ASC Si Emulation ModeEpson LQ or FX Emulation Mode Appendix F. Connector PIN Configuration Parallel Interface Pin Number Signal NameSerial Interface Pin Number Signal Name Pin assignments for typical ATs and compatibles Following is an example of a status sheet printout Appendix G. Status Sheet