Epson U230 manual Drawer Kick-out Connector, Drawer Kick-out Specifications, Limitations

Page 66

Confidential

Drawer Kick-out Connector

The signal specified by the ESC p command is output to this connector. The host can check the status of input signal by the following commands.

•DLE EOT

•GS r

•GS a (ASB)

Drawer Kick-out Specifications

Item		Specifications
Pin assignment		See “Drawer kick-out connector pin assignment”
		table

Model	Printer side	Molex 52018-6615 (or equivalent)

	User side	6-position 6-contact (RJ12 telephone jack)

Drawer kick drive signal	Output voltage	Approx. 24 V

	Output current	1A or less

	Output waveform

t1⋅

2 ms

t2⋅ 2 ms

Outputs the waveforms in the figure “Drawer

circuitry”. (The ESC p command specifies ON

time t1 and OFF time t2.)

Drawer open/close signal

Input signal level

"L"= 0 V

(connector pin )

"H"= 2Å`5 V

Connector appearance

1

6

Limitations

❏The resistance of the drawer kick-out solenoid must not be less than that specified (24 Ω). Otherwisee, an overcurrent could damage the solenoid.

❏Drawer kick-out cable must be shielded.

Appendix A-8Specifications

Image 66

Contents Developer’s guide TM-U230 Confidentiality Agreement Revision Information Key to Symbols Safety PrecautionsConfidential Moduler Connector About This GuideRelated Software and Documents Developer’s Guide Appendix a Specifications Installation and Positioning of TM-U230 Selecting a Place of InstallationEnvironment Specifications External Dimensions Dip Switch Settings DIP Switch Serial InterfaceParallel Interface Ethernet Interface Settings for Horizontal Installation Changing the Location of the Rubber FeetChanging the Orientation of Near End Sensor Attaching Switch Panel for Horizontal Installation Assembling the Power Box Vertical Installation Horizontal Installation and Wall Mounting Installation Wall MountingInstalling the wall mount Secure the mount to the wall using all the 10 screw holesAttaching the hangers Connecting a Host PC Attaching the printer to the wallSerial interface connections Connecting to a parallel interface Connecting to a USB interfaceConnecting to an Ethernet interface Ethernet test switch Names of partsEthernet LEDs Interface cable connectionsDrawer Kick-Out Connector Marked DK 22Installation Important Safety Information HandlingWaterproof Second Digit Ability to keep water out Waterproof mechanism Replacing roll paper Cutting roll paperPrinter is offline as long as the LED is flashing 6Handling Replacing the ribbon cassette Autocutter lock lever8Handling Removing paper jams Paper jams in the vicinity of the print head10Handling Be sure to properly secure the cover with the screw Paper jam in the auto cutter 11 Normal auto cutter positionInstalling the power button cover 12 Installing the power button cover14Handling Paper roll end settings Internal Buzzer2Compatibility Receive Buffer Mounted Mechanism 254, 255 SpaceSaving Space for Receipt Printing GS V Function BGS V Function C Printing direction Executing a cut Assumed A/C position Assumed head position 9999999999999999 Execute GS V 98 Usage of DirectIO in Opos Contorol of The Buzzer TM-U230 41=1B284105006164050A0A Printer.font.Name = ControlA Printer.Print a Printer.EndDoc Printing Specifications Character SpecificationsPaper Specifications Autocutter SpecificationsElectrical Specifications Environmental SpecificationsPrinting Area Appendix A-4Specifications Figure A-4 Without the power supply cover External AppearanceAppendix A-6Specifications Specifications Appendix A-7 Drawer Kick-out Connector Drawer Kick-out SpecificationsLimitations Pin Assignment Drawer CircuitryAppendix A-10 Specifications Appendix B Comparison table AppendixC-2 AppendixC-3 AppendixC-4 AppendixC-5 AppendixC-6 Confidential Seiko Epson Corporation