Toshiba GN-1010 manual File Management

Page 44

File Management

This function is used to obtain the version numbers of the devices connected to the net- work and to upgrade the firmware or read/write the settings file for the device selected on the "Access Point List".

If upgrading the firmware is attempted using the files other than specified, performance will not be guaranteed. Ensure that you use only the specified file.

3 4 5 6

1

2

7

8

1.	[Type]	Selects setting file.
		Firmware/Configuration File/Firmware (Wireless Card)/
		MAC Address Filter File/Protocol Filter File
2.	[Directory Name]	Selects file name or directory name.
3.	[Get Version]	Obtains the version information.
		•	This obtains the verison information from all the devices
			connctected to the same network group, or from only the
			designated device.
		•	To obtain data from a device which exists beyond the IP
			router, always select the device first. In this case, the IP
			parameter must be set correctly.
4.	[Read] (*1)	Reads the firmware and setting file, then saves them on
		the hard disk.
5.	[Write] (*1)	Writes the firmware and setting file saved on the hard disk
		to the selected device.
6.	[Reboot]	Reboots the selected device.
7.	[Exit]	Returns to the main menu.
8.	[Browse]	Browses file name or directory name.

(*1): The file name contains the lower 3 bytes of MAC address of the selected device. (Ex.) [00-80-4C-4D-20-5E] → [4D205E.TXT]

GN-1010 User’s Manual — Functions of the Utility Software

43

Image 44

Contents Operators Manual Handling Precautions Precautions for USEAbout Toshiba Wireless Solution Wireless LAN Adapter TypesWireless LAN Adapters Wireless InteroperabilityWireless LAN and your Health Safety Instruction for Wireless ProductsLimitation of Liability Usage RestrictionsPage Europe EU Declaration of Conformity Regulatory InformationCanada Industry Canada IC USA-Federal Communications Commission FCC ΜΕ ΤΗΝ Παρουσαtoshiba TEC ∆ΗΛΩΝΕΙ ΟΤΙ FX-DS110-APL GN-1010Precautions Related to Service Before Using Product Product ConfigurationConfiguration List CD-ROMFeatures IntroductionTable of Contents Appendix TroubleshootingFunctions of the Utility Software LED OverviewComponent Locations LED Indicators PowerWRX LinkFunction of DIP Switch DIP SwitchesDIP Switch Default Setting Factory Setting Multi-channel Operation AP2Operating Mode Infrastructure Wi-Fi ModeAccess Point AP Station STPage Using the Utility Software Connecting between the GN-1010 and PCConnection with Cross Cable Connection with HubPreparing the Utility Software Node Registration Enter the access point name and click OK Click Exit to complete the detectionConfiguration Click Read to load the setting of the device Click OK Click the appropriate tab and edit the parametersFunctions of the Utility SOFT- Ware Main Menu ScreenNected to the same network group Configuration Screen Base ESS ID ANY IDWEP WirelessWSL Classifi Parameter Default Description Extended Roaming AP2Extension Speed Control RssiFilter MACMAC Address Filter MAC Address Filter List File LogflistProtocol Filter Protocol Filter List File PrtflistGN-1010 User’s Manual Functions of the Utility Software Registered information is displayed on the MAC Address List GN-1010 User’s Manual Functions of the Utility Software Registered information is displayed on the Protocol List Snmp Spanning TreeFile Management Status Common ItemsEnvironment Interfaces MTUParameter Description Wireless Node RssiBridge Information of this tab is excluded from support Wireless Counter Troubleshooting When Communication FailsCheck Peripheral Environment or Installation Location Check SoftwareWhen Device Does Not Start Check Power LEDProduct Specifications External DimensionsPhysical Specifications AppendixSoftware Specification Input/Output InterfaceGlossary Spectrum Diffusion Transmission ChannelBridge RouterPage Page Page GN-1010 Kanda NISHIKI-CHO, CHIYODA-KU, TOKYO, 101-8442, Japan