Toshiba B-SX5T SERIES, BSX5TTS25QMR, BSX5TTS22QMR owner manual Printer Setup, Precautions

Page 11

2. PRINTER SETUP

ENGLISH VERSION EO1-33036

2.1 Precautions

2. PRINTER SETUP

2.1 Precautions

This section outlines the procedures to setup your printer prior to its operation. The section includes precautions, connecting cables, assembling accessories, loading media and ribbon, inserting the optional memory card, and performing a test print.

To insure the best operating environment, and to assure the safety of the operator and the equipment, please observe the following precautions.

∙Operate the printer on a stable, level, operating surface in a location free from excessive humidity, high temperature, dust, vibration or direct sunlight.

∙Keep your work environment static free. Static discharge can cause damage to delicate internal components.

∙Make sure that the printer is connected to a clean source of AC Power and that no other high voltage devices that may cause line noise interference are connected to the same mains.

∙Assure that the printer is connected to the AC mains with a three- prong power cable that has the proper ground (earth) connection.

∙Do not operate the printer with the cover open. Be careful not to allow fingers or articles of clothing to get caught into any of the moving parts of the printer especially the optional cutter mechanism.

∙Make sure to turn off the printer power and to remove the power cord from the printer whenever working on the inside of the printer such as changing the ribbon or loading the media, or when cleaning the printer.

∙For best results, and longer printer life, use only TOSHIBA TEC recommended media and ribbons.

∙Store the media and ribbons in accordance with their specifications.

∙This printer mechanism contains high voltage components; therefore you should never remove any of the covers of the machine as you may receive an electrical shock. Additionally, the printer contains many delicate components that may be damaged if accessed by unauthorised personnel.

∙Clean the outside of the printer with a clean dry cloth or a clean cloth slightly dampened with a mild detergent solution.

∙Use caution when cleaning the thermal print head as it may become very hot while printing. Wait until it has had time to cool before cleaning. Use only the TOSHIBA TEC recommended print head cleaner to clean the print head.

∙Do not turn off the printer power or remove the power plug while the printer is printing or while the ON LINE lamp is blinking.

E2- 1

Page 10 Page 12
Image 11
Page 10 Page 12
Contents SX5T Series Vorsicht CE Compliance for EU onlyWkhsoxj Request Regarding Maintenance PrecautionsTable of Contents EA4-1 EA1-1EA2-1 EA3-1Unpacking Introduction FeaturesProduct Overview Accessories Rear View DimensionsAppearance Front ViewInterior Operation PanelPrecautions Printer SetupProcedure before Operation Gori Connecting the Cables to Your PrinterConnecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Parts, be sure to load Loading the MediaDo not over-tighten the Locking Ring of the Supply Holder Setting the Black Mark Sensor position Setting the Feed Gap Sensor positionSTANDARD/PEEL OFF position Batch modeStrip mode Adjustment Build-in rewinder modeCut mode Loading the Ribbon Auto Ribbon Saving Mode Pcmcia Cards Test Print 3517$5&2 Printer’s power OFF then back to on and check that the LCD Sample of the bar code test print label Operation Panel On Line ModeOperation ResetDump Mode Print Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter Module Care/Handling of the Media and RibbonRestart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsPossible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Do not use any tool that may damage the Print Head Removing Jammed MediaThreshold setting procedure Threshold SettingModel Appendix 1 SpecificationsA1.1 Printer Label A1.2 OptionsA1.3 Media A1.3.1 Media TypeLabel A1.3.2 Detection Area of the Transmissive SensorTag paper with square holes A1.3.3 Detection Area of the Reflective SensorA1.3.4 Effective Print Area Figure below shows the effective print area on the media A1.4 RibbonAppendix 2 Messages and Leds Symbols in the message67$9$ „Interface Cables Appendix 3 InterfaceAppendix 4 Print Samples EAN13+5 digits Interleaved 2 CODE39 StandardJAN13, EAN13 EAN13+2 digitsIndustrial 2 UPC-A+5 digitsBar code GlossariesUSB Universal Serial Bus Print head elementIndex Index Page Page EO1-33036B
Related manuals
Manual 120 pages 3.28 Kb
Top Page Image Contents