Toshiba BSX5TTS25QMR Turning the Printer, Turning on the Printer, Turning OFF the Printer

Page 15

2. PRINTER SETUP

ENGLISH VERSION EO1-33036

2.6 Turning the Printer ON/OFF

2.6Turning the Printer

ON/OFF

2.6.1 Turning ON the Printer

CAUTION!

Use the power switch to turn the printer On/Off. Plugging or unplugging the Power Cord to turn the printer On/Off may cause fire, an electric shock, or damage to the printer.

When the printer is connected to your host computer it is good practice to turn the printer ON before turning on your host computer and turn OFF your host computer before turning off the printer.

1.To turn ON the printer power, press the Power Switch as shown in the diagram below. Note that ( ) is the power ON side of the switch.

Power Switch

NOTE:

If a message other than ON LINE appears on the display or the ERROR LED lamp is illuminated, go to Section 5.1, Error Messages.

2.6.2 Turning OFF the Printer

CAUTION!

1.Do not turn off the printer power while the media is being printed as this may cause a paper jam or damage to the printer.

2.Do not turn off the printer power while the ON LINE lamp is blinking as this may cause damage to your computer.

2.Check that the ON LINE message appears in the LCD Message Display and that the ON LINE and POWER LED lights are illuminated.

1.Before turning off the printer Power Switch verify that the ON LINE message appears in the LCD Message Display and that the ON LINE LED light is on and is not flashing.

2.To turn OFF the printer power press the Power Switch as shown in the diagram below. Note that ({) is the power OFF side of the switch.

Power Switch

E2- 5

Image 15

Contents SX5T Series Vorsicht CE Compliance for EU onlyWkhsoxj Request Regarding Maintenance PrecautionsTable of Contents EA4-1 EA1-1EA2-1 EA3-1Introduction Features Product OverviewUnpacking Accessories Rear View DimensionsAppearance Front ViewInterior Operation PanelPrecautions Printer SetupProcedure before Operation Gori Connecting the Cables to Your PrinterConnecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Parts, be sure to load Loading the MediaDo not over-tighten the Locking Ring of the Supply Holder Setting the Black Mark Sensor position Setting the Feed Gap Sensor positionBatch mode Strip modeSTANDARD/PEEL OFF position Adjustment Build-in rewinder modeCut mode Loading the Ribbon Auto Ribbon Saving Mode Pcmcia Cards Test Print 3517$5&2 Printer’s power OFF then back to on and check that the LCD Sample of the bar code test print label Operation Panel On Line ModeOperation ResetDump Mode Maintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Care/Handling of the Media and RibbonRestart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsPossible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Do not use any tool that may damage the Print Head Removing Jammed MediaThreshold setting procedure Threshold SettingAppendix 1 Specifications A1.1 PrinterModel Label A1.2 OptionsA1.3 Media A1.3.1 Media TypeLabel A1.3.2 Detection Area of the Transmissive SensorA1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaTag paper with square holes Figure below shows the effective print area on the media A1.4 RibbonAppendix 2 Messages and Leds Symbols in the message67$9$ „Interface Cables Appendix 3 InterfaceAppendix 4 Print Samples EAN13+5 digits Interleaved 2 CODE39 StandardJAN13, EAN13 EAN13+2 digitsIndustrial 2 UPC-A+5 digitsBar code GlossariesUSB Universal Serial Bus Print head elementIndex Index Page Page EO1-33036B

Related manuals

Manual 120 pages 3.28 Kb