Toshiba BSX5TTS22QMR, BSX5TTS25QMR, B-SX5T SERIES Appendix 3 Interface, „Interface Cables

Page 46

APPENDIX 3 INTERFACE

ENGLISH VERSION EO1-33036

APPENDIX 3 INTERFACE

APPENDIX 3 INTERFACE

„Interface Cables

To prevent radiation and reception of electrical noise, the interface cables must meet the following requirements:

∙Fully shielded and fitted with metal or metallised connector housings.

∙Keep as short as possible.

∙Should not be bundled tightly with power cords.

∙Should not be tied to power line conduits.

„RS-232C Cable description

The serial data cable used to connect the printer to the host compute should be one of the following two types:

DB-9S

Connector to PC

Pin No. Signal

1N.C.

2RXD

3TXD

4DTR

5GND

6DSR

7RTS

8CTS

9N.C. Housing Shield

DB-25P

Connector to Printer

Pin No.	Signal
1	F.G.
2	RXD
3	TXD
4	CTS
5	RTS
6	DTR
7	SG
20	DSR

DB-25S								DB-25P
Connector to PC								Connector to Printer
Pin No.	Signal							Pin No.	Signal
1	Shield							1	F.G.

2	TXD							2	RXD


3	RXD							3	TXD
3	RXD							3	TXD

4	RTS							4	CTS
4	RTS							4	CTS
5	CTS							5	RTS


6	DSR							6	DTR



7	GND							7	SG



20	DTR							20	DSR
20	DTR							20	DSR

NOTE:

Use an RS-232C cable with the connector including inch type securing screws for the QQ model or metric type securing screws for the QP model.

EA3-1

Image 46

Contents SX5T Series CE Compliance for EU only VorsichtWkhsoxj Precautions Request Regarding MaintenanceTable of Contents EA3-1 EA1-1EA2-1 EA4-1Product Overview Introduction FeaturesUnpacking Accessories Front View DimensionsAppearance Rear ViewOperation Panel InteriorPrinter Setup PrecautionsProcedure before Operation Connecting the Cables to Your Printer GoriConnecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Loading the Media Parts, be sure to loadDo not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Setting the Black Mark Sensor positionStrip mode Batch modeSTANDARD/PEEL OFF position Build-in rewinder mode AdjustmentCut mode Loading the Ribbon Auto Ribbon Saving Mode Pcmcia Cards 3517 Test Print$5&2 Printer’s power OFF then back to on and check that the LCD Sample of the bar code test print label On Line Mode Operation PanelReset OperationDump Mode Cleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Care/Handling of the Media and Ribbon Optional Cutter ModuleError Messages Problems/Causes Solutions TroubleshootingError Messages Restart keyError Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Removing Jammed Media Do not use any tool that may damage the Print HeadThreshold Setting Threshold setting procedureA1.1 Printer Appendix 1 SpecificationsModel A1.3.1 Media Type A1.2 OptionsA1.3 Media LabelA1.3.2 Detection Area of the Transmissive Sensor LabelA1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorTag paper with square holes A1.4 Ribbon Figure below shows the effective print area on the mediaSymbols in the message Appendix 2 Messages and Leds67$9$ Appendix 3 Interface „Interface CablesAppendix 4 Print Samples EAN13+2 digits Interleaved 2 CODE39 StandardJAN13, EAN13 EAN13+5 digitsUPC-A+5 digits Industrial 2Glossaries Bar codePrint head element USB Universal Serial BusIndex Index Page Page EO1-33036B

Related manuals

Manual 120 pages 3.28 Kb