Toshiba BSX5TTS22QMR, BSX5TTS25QMR owner manual Batch mode, Strip mode, STANDARD/PEEL OFF position

Page 19

2. PRINTER SETUP

ENGLISH VERSION EO1-33036

2.7 Loading the Media

2.7Loading the Media (Cont.)

NOTES:

1.Be sure to set the Selection Switch to STANDARD/ PEEL OFF position.

2.The backing paper is easier to feed back to the Take-Up Spool if the Front Plate is removed.

3.Fit the Take-Up Clip so that the longer side of the clip is fitted into the shallow groove in the Take-Up Spool.

4.The backing paper can be wound directly onto the Take- up Spool or a paper core. When using the Take-up Spool, detach the Holder Stopper by removing the B- 3x4 screw. Otherwise, it may be difficult to pull out the wound backing paper roll. .

Holder Stopper

B-3x4 Screw

Take-up Spool

Take-up Clip

When using a paper core, put the core on the Take-up Spool with the Holder Stopper on it, and attach the top edge of the backing paper to the core with adhesive tape. The Take-up Clip is not necessary.

This winding method is applicable to the Built-in Rewinder mode.

12.There are four issue modes available on this printer. How to set the media for each mode is provided below.

Batch mode

In the batch mode, the media is continuously printed and fed until the number of labels/tags specified in the issue command have been printed.

Strip mode

In the strip mode, the backing paper is automatically removed from the label at the Strip Plate as each label is printed.

(1)Remove enough labels from the leading edge of the media to leave 500mm of backing paper free.

(2)Insert the backing paper under the Strip Plate.

(3)Wind the backing paper onto the Take-up Spool and fix it in position with the Take-up Clip. (Wind the paper counterclockwise around the spool as this is the direction it rotates.)

(4)Rotate the Take-up Spool anti-clockwise a few times to remove any slack in the backing paper.

(5)Set the Selection Switch mounted on the Rewinder Assembly to

STANDARD/PEEL OFF position.

Take-up Spool

Front Plate

Take-up Clip

Black Screw Strip Plate Backing Paper

E2- 9

Page 18 Page 20
Image 19
Page 18 Page 20
Contents SX5T Series Vorsicht CE Compliance for EU onlyWkhsoxj Request Regarding Maintenance PrecautionsTable of Contents EA4-1 EA1-1EA2-1 EA3-1Product Overview Introduction FeaturesUnpacking Accessories Rear View DimensionsAppearance Front ViewInterior Operation PanelPrecautions Printer SetupProcedure before Operation Gori Connecting the Cables to Your PrinterConnecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Parts, be sure to load Loading the MediaDo not over-tighten the Locking Ring of the Supply Holder Setting the Black Mark Sensor position Setting the Feed Gap Sensor positionStrip mode Batch modeSTANDARD/PEEL OFF position Adjustment Build-in rewinder modeCut mode Loading the Ribbon Auto Ribbon Saving Mode Pcmcia Cards Test Print 3517$5&2 Printer’s power OFF then back to on and check that the LCD Sample of the bar code test print label Operation Panel On Line ModeOperation ResetDump Mode Cleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Care/Handling of the Media and RibbonRestart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsError Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Do not use any tool that may damage the Print Head Removing Jammed MediaThreshold setting procedure Threshold SettingA1.1 Printer Appendix 1 SpecificationsModel Label A1.2 OptionsA1.3 Media A1.3.1 Media TypeLabel A1.3.2 Detection Area of the Transmissive SensorA1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorTag paper with square holes Figure below shows the effective print area on the media A1.4 RibbonAppendix 2 Messages and Leds Symbols in the message67$9$ „Interface Cables Appendix 3 InterfaceAppendix 4 Print Samples EAN13+5 digits Interleaved 2 CODE39 StandardJAN13, EAN13 EAN13+2 digitsIndustrial 2 UPC-A+5 digitsBar code GlossariesUSB Universal Serial Bus Print head elementIndex Index Page Page EO1-33036B
Related manuals
Manual 120 pages 3.28 Kb
Top Page Image Contents