Toshiba BSX5TTS22QMR, BSX5TTS25QMR, B-SX5T SERIES owner manual 3517, Test Print

Page 25

2. PRINTER SETUP

ENGLISH VERSION EO1-33036

2.10 Test Print

2.10 Test Print

NOTES:

1.Select the sensor type which matches the media being used. Basically, the Reflective Sensor (Black Mark Sensor) is for tag paper, and the Transmissive Sensor (Feed Gap Sensor) is for labels.

2.Select the print mode which matches the media being used. Basically, the thermal transfer is with ribbon, and the thermal direct is without ribbon.

A print test should be performed to check that the printer is operating correctly.

The following paragraphs guide you through the diagnostic procedure for test label printing. Please follow the step-by-step procedures exactly for

 

following￿￿!',$*message.￿ ￿￿￿$

best results.

 

 

 

1.

Use label stock for the test print. For best results, use labels that are

 

76 mm or longer in length.

2.

Press and hold the [FEED] and [PAUSE] keys while turning on the

 

printer power switch. The LCD Message Display will show the

3.

appear￿￿!7(67.

3517

 

Press the

[FEED] key three times to advance to the test print mode as

 

35,17&21',7,21

 

 

indicated￿￿!7(67by

35,17the following message in the LCD Message Display.

4.

￿￿!76735,17

 

Press the

[PAUSE] key and the print condition setting display will

5.

,668(

&2817

￿

Press the

[PAUSE]

key and the issue count setting display will

 

35,1763(('￿¥￿V

 

appear. Set the issue count with the [FEED] or [RESTART] key.

6.

Press the

[PAUSE] key and the print speed setting display will

 

appear.￿￿!7(67Set the35,17print speed with the [FEED] or [RESTART] key.

7. Press the [PAUSE] key and the sensor type setting display will appear￿￿￿￿6(16257!7(6735,17!7(673,7. Select5$the16sensor￿ type with the [FEED] or [RESTART] key.

8. Press3577<3(the [PAUSE]75$16)5key and the print mode setting display will appear. Select the print mode with the [FEED] or [RESTART] key.

E2-15

Page 24 Page 26
Image 25
Page 24 Page 26
Contents SX5T Series Vorsicht CE Compliance for EU onlyWkhsoxj Request Regarding Maintenance PrecautionsTable of Contents EA2-1 EA1-1EA3-1 EA4-1Product Overview Introduction FeaturesUnpacking Accessories Appearance DimensionsFront View Rear ViewInterior Operation PanelPrecautions Printer SetupProcedure before Operation Gori Connecting the Cables to Your PrinterConnecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Parts, be sure to load Loading the MediaDo not over-tighten the Locking Ring of the Supply Holder Setting the Black Mark Sensor position Setting the Feed Gap Sensor positionStrip mode Batch modeSTANDARD/PEEL OFF position Adjustment Build-in rewinder modeCut mode Loading the Ribbon Auto Ribbon Saving Mode Pcmcia Cards Test Print 3517$5&2 Printer’s power OFF then back to on and check that the LCD Sample of the bar code test print label Operation Panel On Line ModeOperation ResetDump Mode Cleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Care/Handling of the Media and RibbonError Messages TroubleshootingError Messages Problems/Causes Solutions Restart keyError Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Do not use any tool that may damage the Print Head Removing Jammed MediaThreshold setting procedure Threshold SettingA1.1 Printer Appendix 1 SpecificationsModel A1.3 Media A1.2 OptionsA1.3.1 Media Type LabelLabel A1.3.2 Detection Area of the Transmissive SensorA1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorTag paper with square holes Figure below shows the effective print area on the media A1.4 RibbonAppendix 2 Messages and Leds Symbols in the message67$9$ „Interface Cables Appendix 3 InterfaceAppendix 4 Print Samples JAN13, EAN13 Interleaved 2 CODE39 StandardEAN13+2 digits EAN13+5 digitsIndustrial 2 UPC-A+5 digitsBar code GlossariesUSB Universal Serial Bus Print head elementIndex Index Page Page EO1-33036B
Related manuals
Manual 120 pages 3.28 Kb
Top Page Image Contents