Toshiba BSX5TTS22QMR, BSX5TTS25QMR A1.2 Options, A1.3 Media, A1.3.1 Media Type, Label, Tag paper

Page 40

APPENDIX 1 SPECIFICATIONS	ENGLISH VERSION EO1-33036
	A1.2 Options

A1.2 Options

Option Name	Type	Description
Swing cutter module	B-4205-QM	A stop and cut swing cutter.
Rotary cutter module	B-8204-QM	Rotary cutter
PCMCIA interface	B-9700-PCM-QM	This board enables the use of the following PCMCIA cards.
board		LAN card: 3 COM 3CCE589ET (recommended)
		ATA card: Conforming to PC card ATA standard
		Flash memory card: 1MB and 4MB cards (See Section 2.9.)
Built-in LAN	B-9700-LAN-QM	This board enables the printer to be used in a LAN network.
interface board
USB interface board	B-9700-USB-QM	Installing this board enables a connection to a PC which has a
		USB interface.

NOTE:

To purchase the optional kits, please contact the nearest authorised TOSHIBA TEC representative or TOSHIBA TEC Head Quarters.

A1.3 Media

Please make sure that the media being used is approved by TOSHIBA TEC. The warranty does not apply when a problem is caused by using media that is not approved by TOSHIBA TEC.

For information regarding TOSHIBA TEC approved media, please contact a TOSHIBA TEC authorised service representative.

A1.3.1 Media Type

Two types of media can be loaded for this thermal transfer and direct thermal printer: label or tag. The table below shows size and shape of the media available for this printer.

Stop position

Cut position

	Black Mark		Black Mark
Label	(on reverse side) Refer to	Tag paper	(on reverse side)
Label	NOTED3 below.	Tag paper

k		positionStop k
		C?	D
		Cut position
		@
		A	?
j	E
		E
	B	Feed Direction
	A

EA1- 2

Image 40

Contents SX5T Series CE Compliance for EU only VorsichtWkhsoxj Precautions Request Regarding MaintenanceTable of Contents EA1-1 EA2-1EA3-1 EA4-1Product Overview Introduction FeaturesUnpacking Accessories Dimensions AppearanceFront View Rear ViewOperation Panel InteriorPrinter Setup PrecautionsProcedure before Operation Connecting the Cables to Your Printer GoriConnecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Loading the Media Parts, be sure to loadDo not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Setting the Black Mark Sensor positionStrip mode Batch modeSTANDARD/PEEL OFF position Build-in rewinder mode AdjustmentCut mode Loading the Ribbon Auto Ribbon Saving Mode Pcmcia Cards 3517 Test Print$5&2 Printer’s power OFF then back to on and check that the LCD Sample of the bar code test print label On Line Mode Operation PanelReset OperationDump Mode Cleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Care/Handling of the Media and Ribbon Optional Cutter ModuleTroubleshooting Error MessagesError Messages Problems/Causes Solutions Restart keyError Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Removing Jammed Media Do not use any tool that may damage the Print HeadThreshold Setting Threshold setting procedureA1.1 Printer Appendix 1 SpecificationsModel A1.2 Options A1.3 MediaA1.3.1 Media Type LabelA1.3.2 Detection Area of the Transmissive Sensor LabelA1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorTag paper with square holes A1.4 Ribbon Figure below shows the effective print area on the mediaSymbols in the message Appendix 2 Messages and Leds67$9$ Appendix 3 Interface „Interface CablesAppendix 4 Print Samples Interleaved 2 CODE39 Standard JAN13, EAN13EAN13+2 digits EAN13+5 digitsUPC-A+5 digits Industrial 2Glossaries Bar codePrint head element USB Universal Serial BusIndex Index Page Page EO1-33036B

Related manuals

Manual 120 pages 3.28 Kb