Toshiba B-EV4D owner manual E2-16

Page 27

2. PRINTER SETUP

ENGLISH VERSION EO1-33088

2.8 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities

2.8.2Self Print Test and Dump Mode (Cont.)

The test print contents should be changed by the following commands and parameters:

PROGRAM VERSION: VX.XX XXXX ---

Firmware version and checksum

TONE ADJUST: +XX -------------------------

Print tone fine adjustment value

FEED ADJUST: +XX.Xmm ------------------

Print position fine adjustment value

CUT POSITION ADJUST: +XX.Xmm -----

Cut position fine adjustment value

BACKFEED ADJUST: +XX.Xmm ----------

Back feed amount fine adjustment value

PARAMETER: [PC-850][0] -----------------

Character code selection and Font “0”

 

selection

[9600][8][1][NONE][2] ---

Baud rate, Data length, Stop bit length,

 

Parity, and Transmission control of RS-

 

232C

[ON][AUTO][FEED][B0]-----

Forward feed wait function, Control code,

 

Feed key function, and Euro code

X-COORDINTE ADJUST: +XX.Xmm -----

X-coordinate fine adjustment value

SENSOR SELECTION: TRANSMISSIVE - Sensor selection and sensitivity

SENSOR ADJ. VALUE:

Sensor setting value

TRANSMISSIVE[XX] REFLECTIVE[XX] --

PRINT SPEED: 5IPS ---------------------------

Print Speed

FLASH ROM:4MB -----------------------------

Flash ROM Capacity

SDRAM: 8MB-----------------------------------

SDRAM Capacity

USER MEMORY: [X KB][0 KB] ------------

User Memory Capacity

TTF AREA: [XXXKB][XXXKB]------------

True type font storage area, Main PC board

 

and optional memory card

EXT CHAR AREA: [XXXKB][XXXKB] --

Writable character storage area, Main PC

 

board and optional memory card

BASIC AREA: [XXXKB][XXXKB] --------

BASIC file storage area, Main PC board and

 

optional memory card

PC SAVE AREA: [XXXKB][XXXKB] -----

PC save storage area, Main PC board and

 

optional memory card

INFORMATION: -------------------------------

Printed only when some information is

 

stored in the flash ROM

TOTAL FEED-----------------------------------

Total feed distance

TOTAL PRINT: 0.00 km ----------------------

Total Print distance

TOTAL CUT: 0 ---------------------------------

Total Cut Count

IP ADDRESS: 192.168.10.20 -----------------

 

SUBNET MASK: 255.255.255.0 -------------

 

GATEWAY: 0.0.0.0 ----------------------------

 

MAC ADDRESS: XX-XX-XX-XX-XX ----

 

DHCP: Disabled---------------------------------

Network setting values

DHCP CLIENT ID:

 

FFFFFFFFFFFFFFFFFFFF FFFFFFFFFFFF ----

SOCKET COMM.: Enabled-------------------

SOCKET COMM. PORT: 08000-------------

E2-16

Image 27
Contents EV4D Series Vorsicht CE Compliance for EU onlyMeanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents For EU only EA2-1Product Overview Introduction Features Unpacking AccessoriesSVT H05VV-F When purchasing the power cordDimensions Front View AppearanceRear View Interior Printer status Button and Indicator LampPrecautions Printer SetupProcedure before Operation Turning the PrinterTurning on the Printer Turning OFF the Printer Connecting the Cables to the Printer Connecting the Power Adapter and the Power Cord Opening/Closing the Top Cover To open the Top CoverTo close the Top Cover Loading the Media Open the Media Holders 1 Media Sensor Calibration Batch mode How to set the media Strip mode OptionCut mode Option How to Load Fanfold Paper StockExternal Media Roll Hanger Option Test, and Dump Mode different type Utilities Media SensorMedia Sensor Calibration Print test label sample Self Print Test and Dump ModeE2-16 How to Use an SD Card „ Inserting an SD Card„ Removing an SD Card Maintenance CleaningPrint Head Media Housing Platen/SensorsCover Option Care/Handling of the MediaTroubleshooting Guide TroubleshootingStatus Lamp Color Status Cause SolutionsRemoving Jammed Media A1.1 Printer Appendix 1 SpecificationsEV4D-TS14-QM-R Label A1.2 OptionsA1.3 Media A1.3.1 Media TypeA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaBlack Mark Figure below shows the effective print area on the media Interface Cables Appendix 2 InterfaceBar code GlossariesSupply EO1-33088C