Toshiba G8000 Series operation manual LCD/LED Legend, Name Function

Page 37

 

 

Table 9 - LCD/LED Legend.

 

 

 

 

No.

Name

 

Function

 

 

 

 

11

 

 

LCD indicates operation procedure, measured data and

 

LCD

 

warnings/faults.

 

 

 

 

 

 

Detailed in the section titled "LCD Display."

 

 

 

 

12

UPS SUPPLY LED

 

Turned on while the inverter is on. Flashes during start-up

 

 

or stop procedure.

 

 

 

 

 

 

 

13

WARNING LED

 

Normally off. Turned on with warnings, flashes with AC

 

 

input abnormality.

 

 

 

 

 

 

 

14

FAULT LED

 

Normally off. Turned on with faults.

 

 

 

 

15

AC INPUT LED

 

Normally on with regular AC input. Flashes with AC

 

 

input under-voltage (85%).

 

 

 

 

 

 

 

16

RECTIFIER LED

 

Turned on after DC caps are charged up through the

 

 

rectifier.

 

 

 

 

 

 

 

17

INVERTER LED

 

Flashes during start-up or stop procedure. Turned on after

 

 

the inverter starts up, and during available.

 

 

 

 

 

 

 

18

AC OUTPUT LED

 

Turned on with AC output fed by either the bypass or

 

 

inverter sources.

 

 

 

 

 

 

 

19

BATTERY LED

 

Turned on with battery connected. (Aux-contact on)

 

 

 

 

20

FLOAT CHARGE LED

 

Turned on during float charge.

 

 

 

 

21

EQUALIZE CHARGE LED

 

Turned on during equalize charge or protection charge

 

 

with battery OH contact open.

 

 

 

 

 

 

 

22

DISCHARGE LED

 

Turned on during battery discharge.

 

 

 

 

23

BYPASS INPUT LED

 

Normally on with regular bypass input. Flashes with bypass

 

 

under-voltage (85%).

 

 

 

 

 

 

 

24

UPS LED

 

Turned on during UPS Supply.

 

 

 

 

25

BYPASS LED

 

Turned on during Bypass Supply.

36

Image 37
Contents Document Number February Uninterruptible Power System UPS G8000 SeriesIntroduction Uninterruptible Power Supply Contacting Toshiba’s Customer Support Center Manual’s Purpose and ScopeTable of Contents Safety Alert Symbol General Safety InstructionsSpecial Symbols Qualified Personnel only Maintenance PrecautionsPage Storing Conditions Storage PreparationDisposal Storage MaintenanceConductor Routing and Grounding Installation PrecautionsDo not install the UPS close to a water source UPS is to be installed in a controlled environmentConnect ground wire to the earth ground terminal only MandatoryOperating Precautions Important Safety Instructions Safety Precautions Do not open the front cover Personal injuryDo not remove the rear/side panels Faults by removing these panelsOperators should be certified* personnel UPS exterior showing warning label locations Labeling RequirementsUPS exterior/interior showing warning labels Battery Grounding Electrode Terminal Handling Precautions Do not operate the UPS in wet locations Keep the reset button pressed for 5 seconds to reset the UPSDo not open the front and/or rear panel Outline and LayoutShows the outline dimensions of the 300kVA UPS Recommended Cable Size and Tightening Torque for 150kVA UPS UPS ConnectionsCable knockout plates at the bottom 150 and 225kVA Recommended Cable Size and Tightening Torque for 225kVA UPSRecommended Cable Size and Tightening Torque for 300kVA UPS Battery Bypass InputCable knockout plates at the top 300kVA Recommended LugsOperating Switches Operating SwitchesControl Functions UPS Circuit ConfigurationKey-switch Key-Switch and ButtonsKey-switch function Name Function Remarks Button functions Operating ButtonsName Function Remarks External Connections External ConnectionsLED Indication Graphics InterfaceName Function LCD/LED LegendScroll up Scroll down LCD IndicationAC- I O AC-VOSync VoltDC-V Discharging 15MINBatt No Alarm No Warning No Fault No WarningFuse Blown Another ItemUPS 35H Battery 56MIN Operation Types OperationOperators should be qualified/trained personnel Operate the UPS in the specified conditionPre-operational check ProceduresLED legend Off Flash System InitializePress the RUN button For 0.5 sec Startup Procedures Cont’dPress ‘UPS’ Switch Stop Stopping procedureMove #72B to ‘OFF’ Position Complete Shutdown Step Procedure LCD/LED Status Press ‘RUN’ SwitchComplete Shutdown BATT-V BattFloat Charge LED Float Charge LED is On Equal Charge LED is Off Press FLOAT/EQAUL Button for 0.5 sec Goes awayFloat Charge is On Equal CAHRGE* LED is Off Types of Errors TroubleshootingFault Data Screen LCD Fault DisplaysNumber of the message in the detection order 1 UPS Fault MessagesLCD Message Description Indication LCD Scroll with faults or warnings When the UPS has stopped due to a fault, be sure to removeData needed to determine the cause of the fault UPSChanging screens with scroll buttons Scroll ButtonsRestoring UPS Operation Contact Toshiba in the event of malfunction or faultDo not attempt to modify or relocate the UPS Do not open the front and/or rear panelsGeneral Specification UPS SpecificationsMechanical Specification Rated Capacity 150kVA 120kW 225kVA 180kW 300kVA 240kW Electrical SpecificationWord Definitions Appendix
Related manuals
Manual 41 pages 8 Kb