Actiontec electronic IS560LH user manual VnDCE Response Format, Result Code Option

Page 46

VnDCE Response Format

This command controls whether result codes (including call progress and negotia- tion progress messages) are displayed as words or their numeric equivalents.

	Command		Effect

	V0		Not supported. Results are always text.

	V1		Displays result codes as text (default).

Result Codes:

	OK	n = 0, 1

	ERROR	Otherwise

Wn			Result Code Option

	Command			Effect

	W0			CONNECT result code reports DTE speed. Disable
	W0			protocol result codes.
				protocol result codes.

	W1			CONNECT result code reports DTE speed. Enable
	W1			protocol result codes.
				protocol result codes.

	W2			CONNECT result code reports DCE speed. Enable
	W2			protocol result codes (default).
				protocol result codes (default).

Result Codes:

	OK	n = 0, 1, 2

	ERROR	Otherwise

46

Image 46

Contents Internal Voice/Fax Windows Modem Table of Contents Introduction For Windows 95 and Windows 98 Installations Do This FirstWindows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box Proceed to the section titled Installing the Modem For Windows NT 4.0 InstallationDevices Window Installing The Modem Hardware InstallationInstalling The Modem Connecting Devices To The Modem Connecting DevicesConfiguring Windows Page Page Configuring Windows 95 OEM SR2 FinishPage Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Init String Modem’s Voice FeaturesAT&F&C1&D2W2 Page Troubleshooting Windows 95 and WindowsMore Info Panel Does Not Install Uninstalling the ModemPage Page Common Problems No Dialtone ErrorPage Answer Command AT CommandsRepeat Last Command +++ Escape sequenceResult Codes Communication Standard SettingThis command determines Ccitt vs. Bell standard Carrier ControlDnDial Online Data Character Echo Command Echo CommandHook Control This command sets speaker volume to low, medium, or high Monitor Speaker VolumeRequest ID Information This command turns the speaker on or off Modulation HandshakeResult Code Control Return On-line to Data ModeSelect Pulse Dialing Select Tone DialingVnDCE Response Format Result Code OptionExtended Result Codes Dial Tone DetectRecall Stored Profile Busy Tone DetectLong Space Disconnect Auto RetrainData Carrier Detect DCD Control DTR Control22bis Guard Tone Control Auxiliary Relay optionLocal Flow Control Selection Asynchronous Communications ModeThis Command is effective only for use in Japan Pulse Dial Make-to-Break Ratio SelectionThis command selects DSR action Data Set Ready DSR OptionThis command is used to display the active profiles Below is an example of a possible outputSSE \An Zn=x\Bn Modem Port Flow Control Adjust Bits/s Rate Control\Kn Same as 4.Default \Nn \Tn Inactivity Timer \Vn Protocol Result Code\Xn XON/XOFF Pass Through Data Calling ToneV90=x V.90 Downstream Rate and Control Write to/Read from DSP Register Enable/Disable Data CompressionAT Commands for Testing and Debugging Line-to-Line LoopbackInitial Transmit Carrier Rate 33600 Tion failedAfter initial negotiation Final Receive Carrier Rate 33600 Final Transmit Carrier Rate 33600Rate Tion rateRegisters Reference Range −127, Ascii decimal Default Line feed Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Carriage return Units Range −32 Default Backspace UnitsConnection Completion Time-Out Range Default UnitssecondsComma Dial Modifier Time S12 Escape Guard Time S10 Automatic Disconnect DelayS11 Dtmf Dialing Speed S14 General Bit Mapped Options StatusS21 S24 Timer to Control Sleep ModeS22 S32 S28 Modulation Enable/DisableS30 Inactivity Timer S33S36 S37 Dial Line Rate defaultS38 56K Dial Line Rate default ConnectionS48 Lapm Error Control and Feature Negotiation default S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S40S91 S89 Timer to Control Sleep ModeS90 S92Result Code Summary Description No CarrierPage FCC Part 68 Requirements FCC RegulationsDeclaration of Conformity Canadian Department Of Communications Cdoc