Actiontec electronic IS560LH user manual S89 Timer to Control Sleep Mode, S90, S91, S92

Page 73

The following chart lists the S36 and S48 configuration settings necessary to negoti- ate certain types of connections:

		S48=7	S48 =128
	S36 = 0, 2	LAPM or hangup	do not use
	S36 = 1, 3	LAPM or async	async
	S36 = 4, 6	LPAM, MNP, or hangup	MNP or hangup
	S36 = 5, 7	LAPM, MNP, or async	MNP or async
S89	Timer to Control Sleep Mode
	Range:	0, 5-255
	Default:	10

This command displays the number of seconds of inactivity (no characters sent from the DTE, no RING) in the off-line command state before the modem places itself into standby mode. A value of zero prevents standby mode.

If a number between 1 and 4 is entered for this register, it will set the value to 5, and the inactivity before standby will be 5 seconds. This is done for compatibility with previous products which allowed time-outs down to 1s.

S90	Local Phone Status

0= local phone on-hook

1= local phone off-hook

This register tells the status of the local phone. It is read only.

S91	Line Transmit Level
Range:	6-15
Default:	15
Units:	1 dB

This register is effective only for Japan. It specifies the line transmit level in dB with an implied minus sign.

S92	Direct Connect Transmit Level (default 20)

Sets the transmit level, in dBm for direct connect. This value may have different settings for different phones.

73

Image 73

Contents Internal Voice/Fax Windows Modem Table of Contents Introduction Do This First For Windows 95 and Windows 98 InstallationsWindows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box For Windows NT 4.0 Installation Proceed to the section titled Installing the ModemDevices Window Hardware Installation Installing The ModemInstalling The Modem Connecting Devices Connecting Devices To The ModemConfiguring Windows Page Page Finish Configuring Windows 95 OEM SR2Page Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Init String Modem’s Voice FeaturesAT&F&C1&D2W2 Page Windows 95 and Windows TroubleshootingMore Info Panel Uninstalling the Modem Does Not InstallPage Page No Dialtone Error Common ProblemsPage Repeat Last Command AT CommandsAnswer Command +++ Escape sequenceThis command determines Ccitt vs. Bell standard Communication Standard SettingResult Codes Carrier ControlDnDial Online Data Character Echo Command Echo CommandHook Control This command sets speaker volume to low, medium, or high Monitor Speaker VolumeRequest ID Information Modulation Handshake This command turns the speaker on or offSelect Pulse Dialing Return On-line to Data ModeResult Code Control Select Tone DialingResult Code Option VnDCE Response FormatDial Tone Detect Extended Result CodesLong Space Disconnect Busy Tone DetectRecall Stored Profile Auto RetrainDTR Control Data Carrier Detect DCD ControlAuxiliary Relay option 22bis Guard Tone ControlThis Command is effective only for use in Japan Asynchronous Communications ModeLocal Flow Control Selection Pulse Dial Make-to-Break Ratio SelectionData Set Ready DSR Option This command selects DSR actionBelow is an example of a possible output This command is used to display the active profilesSSE \An Zn=x\Bn Modem Port Flow Control Adjust Bits/s Rate Control\Kn Same as 4.Default \Nn \Vn Protocol Result Code \Tn Inactivity TimerData Calling Tone \Xn XON/XOFF Pass ThroughV90=x V.90 Downstream Rate and Control AT Commands for Testing and Debugging Enable/Disable Data CompressionWrite to/Read from DSP Register Line-to-Line LoopbackInitial Transmit Carrier Rate 33600 Tion failedAfter initial negotiation Rate Final Transmit Carrier Rate 33600Final Receive Carrier Rate 33600 Tion rateRegisters Reference Range −127, Ascii decimal Default Carriage return Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Line feed Units Range −32 Default Backspace UnitsConnection Completion Time-Out Range Default UnitssecondsComma Dial Modifier Time S11 Dtmf Dialing Speed S10 Automatic Disconnect DelayS12 Escape Guard Time S14 General Bit Mapped Options StatusS21 S24 Timer to Control Sleep ModeS22 S30 Inactivity Timer S28 Modulation Enable/DisableS32 S33S38 56K Dial Line Rate default S37 Dial Line Rate defaultS36 ConnectionS43 Auto Mode default 1, range S42 Auto Rate default 1, rangeS48 Lapm Error Control and Feature Negotiation default S40S90 S89 Timer to Control Sleep ModeS91 S92No Carrier Result Code Summary DescriptionPage FCC Part 68 Requirements FCC RegulationsDeclaration of Conformity Canadian Department Of Communications Cdoc