Actiontec electronic IS560LH S28 Modulation Enable/Disable, S30 Inactivity Timer, S32, S33

Page 70

S28	V.34 Modulation Enable/Disable

0= disabled, 1-255 = enabled, Range: 0-255

Default: 1

This register enables/disables V.34 modulation.

S30	Inactivity Timer

Range: 0-255

Default: 0

Units: minutes

S30 specifies the length of time (in minutes) that the modem will wait before discon- necting when no data is sent or received. This function is only applicable to buffer mode.

S32	Synthetic Ring Volume

Range: 0-255

Default: 10

This register specifies a synthetic ring volume in dB with an implied minus sign.

S33	Synthetic Ring Frequency

Range: 0-5

Default: 0

This register specifies a synthetic ring frequency. Valid ranges are 0-5, with 0= dis- abled and 1-5 corresponding to 5 ring frequencies.

S35	Data Calling Tone

0 = disabled, 1 = enableD Range: 0-1

Default: 0

Data Calling Tone is a tone of certain frequency and cadence as specified in V.25 which allows remote Data/FAX/Voice discrimination. The frequency is 1300 Hz with a cadence of .5 s on and 2 s off.

Image 70

Contents Internal Voice/Fax Windows Modem Table of Contents Introduction For Windows 95 and Windows 98 Installations Do This FirstWindows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box Proceed to the section titled Installing the Modem For Windows NT 4.0 InstallationDevices Window Installing The Modem Hardware InstallationInstalling The Modem Connecting Devices To The Modem Connecting DevicesConfiguring Windows Page Page Configuring Windows 95 OEM SR2 FinishPage Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Init String Modem’s Voice FeaturesAT&F&C1&D2W2 Page Troubleshooting Windows 95 and WindowsMore Info Panel Does Not Install Uninstalling the ModemPage Page Common Problems No Dialtone ErrorPage Answer Command AT CommandsRepeat Last Command +++ Escape sequenceResult Codes Communication Standard SettingThis command determines Ccitt vs. Bell standard Carrier ControlDnDial Online Data Character Echo Command Echo CommandHook Control This command sets speaker volume to low, medium, or high Monitor Speaker VolumeRequest ID Information This command turns the speaker on or off Modulation HandshakeResult Code Control Return On-line to Data ModeSelect Pulse Dialing Select Tone DialingVnDCE Response Format Result Code OptionExtended Result Codes Dial Tone DetectRecall Stored Profile Busy Tone DetectLong Space Disconnect Auto RetrainData Carrier Detect DCD Control DTR Control22bis Guard Tone Control Auxiliary Relay optionLocal Flow Control Selection Asynchronous Communications ModeThis Command is effective only for use in Japan Pulse Dial Make-to-Break Ratio SelectionThis command selects DSR action Data Set Ready DSR OptionThis command is used to display the active profiles Below is an example of a possible outputSSE \An Zn=x\Bn Modem Port Flow Control Adjust Bits/s Rate Control\Kn Same as 4.Default \Nn \Tn Inactivity Timer \Vn Protocol Result Code\Xn XON/XOFF Pass Through Data Calling ToneV90=x V.90 Downstream Rate and Control Write to/Read from DSP Register Enable/Disable Data CompressionAT Commands for Testing and Debugging Line-to-Line LoopbackInitial Transmit Carrier Rate 33600 Tion failedAfter initial negotiation Final Receive Carrier Rate 33600 Final Transmit Carrier Rate 33600Rate Tion rateRegisters Reference Range −127, Ascii decimal Default Line feed Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Carriage return Units Range −32 Default Backspace UnitsConnection Completion Time-Out Range Default UnitssecondsComma Dial Modifier Time S12 Escape Guard Time S10 Automatic Disconnect DelayS11 Dtmf Dialing Speed S14 General Bit Mapped Options StatusS21 S24 Timer to Control Sleep ModeS22 S32 S28 Modulation Enable/DisableS30 Inactivity Timer S33S36 S37 Dial Line Rate defaultS38 56K Dial Line Rate default ConnectionS48 Lapm Error Control and Feature Negotiation default S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S40S91 S89 Timer to Control Sleep ModeS90 S92Result Code Summary Description No CarrierPage FCC Part 68 Requirements FCC RegulationsDeclaration of Conformity Canadian Department Of Communications Cdoc

S28

V.34 Modulation Enable/Disable

S30

Inactivity Timer

S32

S33

S35

Data Calling Tone