Actiontec electronic IS560LH user manual

Page 35

Modems section after you have deleted it from the Device Manager. If it is, this could be a sign that your Plug-N-Play settings are not correct. See “Does Not Install” for information about Plug-N-Play.)

3.Close all open programs and return to the Windows desktop. On the Start menu, click Find, then click Files or Folders and search for the files listed below. Type in the name and extension of each and click Find. Once you find each of the files listed, click the file name to select it then on the File menu choose Delete. (Do not delete these files from your modem installation diskette. You will need your diskette to reinstall the modem).

ltcom.vxd ltwave.inf

ltmodem.vxd ltdft.inf

ltvcd.vxd ltdsvd.dll

ltmodem.sys ltports.inf

If you cannot find a particular file, it usually means it was not installed.

Note to users of Windows 95 and 98

If you are using Windows 95 or 98, there are two additional files which may be generateed when installing a piece of hardware from an OEM. The file is called oem#.inf. The number (#) used is generated by Windows 95 each time an additional piece of hardware is installed. In the case of the modem, these files wil have numbers between 1 and 99 reflected in the filename--”oem8.inf ”, for example

On the Start menu, click Find then click Files or Folders. At the first screen, type in *.inf in the Named: box. Make sure your entire drive is selected. Click to select Include subfolders box. Be sure all the information is typed in as shown below.

Before beginning the search, select the Advanced tab.

35

Image 35

Contents Internal Voice/Fax Windows Modem Table of Contents Introduction Do This First For Windows 95 and Windows 98 InstallationsWindows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box For Windows NT 4.0 Installation Proceed to the section titled Installing the ModemDevices Window Hardware Installation Installing The ModemInstalling The Modem Connecting Devices Connecting Devices To The ModemConfiguring Windows Page Page Finish Configuring Windows 95 OEM SR2Page Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page AT&F&C1&D2W2 Modem’s Voice FeaturesInit String Page Windows 95 and Windows TroubleshootingMore Info Panel Uninstalling the Modem Does Not InstallPage Page No Dialtone Error Common ProblemsPage +++ Escape sequence AT CommandsRepeat Last Command Answer CommandCarrier Control Communication Standard SettingThis command determines Ccitt vs. Bell standard Result CodesDnDial Hook Control Echo CommandOnline Data Character Echo Command Request ID Information Monitor Speaker VolumeThis command sets speaker volume to low, medium, or high Modulation Handshake This command turns the speaker on or offSelect Tone Dialing Return On-line to Data ModeSelect Pulse Dialing Result Code ControlResult Code Option VnDCE Response FormatDial Tone Detect Extended Result CodesAuto Retrain Busy Tone DetectLong Space Disconnect Recall Stored ProfileDTR Control Data Carrier Detect DCD ControlAuxiliary Relay option 22bis Guard Tone ControlPulse Dial Make-to-Break Ratio Selection Asynchronous Communications ModeThis Command is effective only for use in Japan Local Flow Control SelectionData Set Ready DSR Option This command selects DSR actionBelow is an example of a possible output This command is used to display the active profilesSSE \Bn Zn=x\An \Kn Adjust Bits/s Rate ControlModem Port Flow Control Same as 4.Default \Nn \Vn Protocol Result Code \Tn Inactivity TimerData Calling Tone \Xn XON/XOFF Pass ThroughV90=x V.90 Downstream Rate and Control Line-to-Line Loopback Enable/Disable Data CompressionAT Commands for Testing and Debugging Write to/Read from DSP RegisterAfter initial negotiation Tion failedInitial Transmit Carrier Rate 33600 Tion rate Final Transmit Carrier Rate 33600Rate Final Receive Carrier Rate 33600Registers Reference Range −32 Default Backspace Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Carriage return Units Range −127, Ascii decimal Default Line feed UnitsComma Dial Modifier Time Range Default UnitssecondsConnection Completion Time-Out S14 General Bit Mapped Options Status S10 Automatic Disconnect DelayS11 Dtmf Dialing Speed S12 Escape Guard TimeS22 S24 Timer to Control Sleep ModeS21 S33 S28 Modulation Enable/DisableS30 Inactivity Timer S32Connection S37 Dial Line Rate defaultS38 56K Dial Line Rate default S36S40 S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S48 Lapm Error Control and Feature Negotiation defaultS92 S89 Timer to Control Sleep ModeS90 S91No Carrier Result Code Summary DescriptionPage Declaration of Conformity FCC RegulationsFCC Part 68 Requirements Canadian Department Of Communications Cdoc