Actiontec electronic IS560LH user manual Proceed to the section titled Installing the Modem

Page 7

Figure 3b: Windows 95 (or 95A) COM2 Disable Panel

Proceed to the section titled “Installing the Modem.”

For Windows NT 4.0 Installation

Remove all other modem drivers from your operating system. On the Start menu, click Settings then click Control Panel. In Control Panel, double-click on the Mo- dems icon. Select the modem you wish to remove and click Remove. Turn off the computer and physically remove the modem from your system. Do not install your new modem at this time. Follow the procedures below. Once you remove the old mo- dem and its drivers from your system, you will need the old modem driver diskette if you wish to reinstall it at a later date.

On the Start menu, click Programs, then click Administrative Tools, then click Windows NT Diagnostics. Click the Version tab. “Service Pack 3” (or greater) should be installed in Windows NT 4.0.

Image 7

Contents Internal Voice/Fax Windows Modem Table of Contents Introduction Do This First For Windows 95 and Windows 98 InstallationsWindows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box For Windows NT 4.0 Installation Proceed to the section titled Installing the ModemDevices Window Hardware Installation Installing The ModemInstalling The Modem Connecting Devices Connecting Devices To The ModemConfiguring Windows Page Page Finish Configuring Windows 95 OEM SR2Page Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Init String Modem’s Voice FeaturesAT&F&C1&D2W2 Page Windows 95 and Windows TroubleshootingMore Info Panel Uninstalling the Modem Does Not InstallPage Page No Dialtone Error Common ProblemsPage +++ Escape sequence AT CommandsRepeat Last Command Answer CommandCarrier Control Communication Standard SettingThis command determines Ccitt vs. Bell standard Result CodesDnDial Online Data Character Echo Command Echo CommandHook Control This command sets speaker volume to low, medium, or high Monitor Speaker VolumeRequest ID Information Modulation Handshake This command turns the speaker on or offSelect Tone Dialing Return On-line to Data ModeSelect Pulse Dialing Result Code ControlResult Code Option VnDCE Response FormatDial Tone Detect Extended Result CodesAuto Retrain Busy Tone DetectLong Space Disconnect Recall Stored ProfileDTR Control Data Carrier Detect DCD ControlAuxiliary Relay option 22bis Guard Tone ControlPulse Dial Make-to-Break Ratio Selection Asynchronous Communications ModeThis Command is effective only for use in Japan Local Flow Control SelectionData Set Ready DSR Option This command selects DSR actionBelow is an example of a possible output This command is used to display the active profilesSSE \An Zn=x\Bn Modem Port Flow Control Adjust Bits/s Rate Control\Kn Same as 4.Default \Nn \Vn Protocol Result Code \Tn Inactivity TimerData Calling Tone \Xn XON/XOFF Pass ThroughV90=x V.90 Downstream Rate and Control Line-to-Line Loopback Enable/Disable Data CompressionAT Commands for Testing and Debugging Write to/Read from DSP RegisterInitial Transmit Carrier Rate 33600 Tion failedAfter initial negotiation Tion rate Final Transmit Carrier Rate 33600Rate Final Receive Carrier Rate 33600Registers Reference Range −32 Default Backspace Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Carriage return Units Range −127, Ascii decimal Default Line feed UnitsConnection Completion Time-Out Range Default UnitssecondsComma Dial Modifier Time S14 General Bit Mapped Options Status S10 Automatic Disconnect DelayS11 Dtmf Dialing Speed S12 Escape Guard TimeS21 S24 Timer to Control Sleep ModeS22 S33 S28 Modulation Enable/DisableS30 Inactivity Timer S32Connection S37 Dial Line Rate defaultS38 56K Dial Line Rate default S36S40 S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S48 Lapm Error Control and Feature Negotiation defaultS92 S89 Timer to Control Sleep ModeS90 S91No Carrier Result Code Summary DescriptionPage FCC Part 68 Requirements FCC RegulationsDeclaration of Conformity Canadian Department Of Communications Cdoc