Actiontec electronic IS560LH Final Transmit Carrier Rate 33600, Final Receive Carrier Rate 33600

Page 64

Description	Example	Comments
Initial Receive Carrier Rate	33600	The download connection
		rate after initial negotiation.
Final Transmit Carrier Rate	33600	The last upload connection
		rate.
Final Receive Carrier Rate	33600	The last download connec-
		tion rate.
Protocol Negotiation Result	V.42	Possible results are: V.42,
		MNP or noEC
Data Compression Result	V.42bis	Possible results are: V.42bis,
		MNP5 or no Compression.
Estimated Noise Level	10	An average of the squared
		error between the received
		constellation point and the
		decision point.
Receive Signal Power Level	20	Receive signal (-dBm)
Transmit Signal Power Level	10	Transmit signal level ( –
		dBm)
Round Trip Delay (msec)	60	Measured Round Trip Delay
		in milliseconds
Near Echo Level (-dBm)	39	Measured Near Echo Level
Far Echo Level (-dBm)	60	Measured Far Echo Level
Transmit Frame Count	5000	Number of HDLC frames
		transmitted.
Transmit Frame Error Count	10	Number of frame errors
		transmitted
Receive Frame Count	5000	Number of HDLC frames
		received.
Receive Frame Error Count	10	Number of frame errors re-
		ceived
Retrain and Rate Negotiate Event	1	Number of retrains initiated
		by the local modem.
Retrain and Rate Negotiate Event	1	Number of retrains initiated
		by the by remote modem.

64

Image 64

Contents Internal Voice/Fax Windows Modem Table of Contents Introduction For Windows 95 and Windows 98 Installations Do This FirstWindows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box Proceed to the section titled Installing the Modem For Windows NT 4.0 InstallationDevices Window Installing The Modem Hardware InstallationInstalling The Modem Connecting Devices To The Modem Connecting DevicesConfiguring Windows Page Page Configuring Windows 95 OEM SR2 FinishPage Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Init String Modem’s Voice FeaturesAT&F&C1&D2W2 Page Troubleshooting Windows 95 and WindowsMore Info Panel Does Not Install Uninstalling the ModemPage Page Common Problems No Dialtone ErrorPage AT Commands Repeat Last CommandAnswer Command +++ Escape sequenceCommunication Standard Setting This command determines Ccitt vs. Bell standardResult Codes Carrier ControlDnDial Online Data Character Echo Command Echo CommandHook Control This command sets speaker volume to low, medium, or high Monitor Speaker VolumeRequest ID Information This command turns the speaker on or off Modulation HandshakeReturn On-line to Data Mode Select Pulse DialingResult Code Control Select Tone DialingVnDCE Response Format Result Code OptionExtended Result Codes Dial Tone DetectBusy Tone Detect Long Space DisconnectRecall Stored Profile Auto RetrainData Carrier Detect DCD Control DTR Control22bis Guard Tone Control Auxiliary Relay optionAsynchronous Communications Mode This Command is effective only for use in JapanLocal Flow Control Selection Pulse Dial Make-to-Break Ratio SelectionThis command selects DSR action Data Set Ready DSR OptionThis command is used to display the active profiles Below is an example of a possible outputSSE \An Zn=x\Bn Modem Port Flow Control Adjust Bits/s Rate Control\Kn Same as 4.Default \Nn \Tn Inactivity Timer \Vn Protocol Result Code\Xn XON/XOFF Pass Through Data Calling ToneV90=x V.90 Downstream Rate and Control Enable/Disable Data Compression AT Commands for Testing and DebuggingWrite to/Read from DSP Register Line-to-Line LoopbackInitial Transmit Carrier Rate 33600 Tion failedAfter initial negotiation Final Transmit Carrier Rate 33600 RateFinal Receive Carrier Rate 33600 Tion rateRegisters Reference Range 0−255 Default UnitsASCII Range −127, Ascii decimal Default Carriage return UnitsRange −127, Ascii decimal Default Line feed Units Range −32 Default Backspace UnitsConnection Completion Time-Out Range Default UnitssecondsComma Dial Modifier Time S10 Automatic Disconnect Delay S11 Dtmf Dialing SpeedS12 Escape Guard Time S14 General Bit Mapped Options StatusS21 S24 Timer to Control Sleep ModeS22 S28 Modulation Enable/Disable S30 Inactivity TimerS32 S33S37 Dial Line Rate default S38 56K Dial Line Rate defaultS36 ConnectionS42 Auto Rate default 1, range S43 Auto Mode default 1, rangeS48 Lapm Error Control and Feature Negotiation default S40S89 Timer to Control Sleep Mode S90S91 S92Result Code Summary Description No CarrierPage FCC Part 68 Requirements FCC RegulationsDeclaration of Conformity Canadian Department Of Communications Cdoc