Actiontec electronic IS560LH user manual

Page 75

CONNECT 34666 EC* CONNECT 36000 EC* CONNECT 37333 EC* CONNECT 38666 EC* CONNECT 40000 EC* CONNECT 41333 EC* CONNECT 42666 EC* CONNECT 44000 EC* CONNECT 45333 EC* CONNECT 46666 EC* CONNECT 48000 EC* CONNECT 49333 EC* CONNECT 50666 EC* CONNECT 52000 EC* CONNECT 53333 EC*

Connection at 34666 bits/s, V.90 rate Connection at 36000 bits/s, V.90 rate Connection at 37333 bits/s, V.90 rate Connection at 38666 bits/s, V.90 rate Connection at 40000 bits/s, V.90 rate Connection at 41333 bits/s, V.90 rate Connection at 42666 bits/s, V.90 rate Connection at 44000 bits/s, V.90 rate Connection at 45333 bits/s, V.90 rate Connection at 46666 bits/s, V.90 rate Connection at 48000 bits/s, V.90 rate Connection at 49333 bits/s, V.90 rate Connection at 50666 bits/s, V.90 rate Connection at 52000 bits/s, V.90 rate Connection at 53333 bits/s, V.90 rate

*EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used:

V42bis—V.42 error control and V.42bis data compression.

V42—V.42 error control only.

MNP 5— MNP class 4 error control and MNP class 5 data compression.

MNP 4— MNP class 4 error control only.

NoEC—No error control protocol.

75

Image 75

Contents Internal Voice/Fax Windows Modem Table of Contents Introduction Do This First For Windows 95 and Windows 98 InstallationsWindows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box For Windows NT 4.0 Installation Proceed to the section titled Installing the ModemDevices Window Hardware Installation Installing The ModemInstalling The Modem Connecting Devices Connecting Devices To The ModemConfiguring Windows Page Page Finish Configuring Windows 95 OEM SR2Page Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Modem’s Voice Features Init StringAT&F&C1&D2W2 Page Windows 95 and Windows TroubleshootingMore Info Panel Uninstalling the Modem Does Not InstallPage Page No Dialtone Error Common ProblemsPage +++ Escape sequence AT CommandsRepeat Last Command Answer CommandCarrier Control Communication Standard SettingThis command determines Ccitt vs. Bell standard Result CodesDnDial Echo Command Online Data Character Echo CommandHook Control Monitor Speaker Volume This command sets speaker volume to low, medium, or highRequest ID Information Modulation Handshake This command turns the speaker on or offSelect Tone Dialing Return On-line to Data ModeSelect Pulse Dialing Result Code ControlResult Code Option VnDCE Response FormatDial Tone Detect Extended Result CodesAuto Retrain Busy Tone DetectLong Space Disconnect Recall Stored ProfileDTR Control Data Carrier Detect DCD ControlAuxiliary Relay option 22bis Guard Tone ControlPulse Dial Make-to-Break Ratio Selection Asynchronous Communications ModeThis Command is effective only for use in Japan Local Flow Control SelectionData Set Ready DSR Option This command selects DSR actionBelow is an example of a possible output This command is used to display the active profilesSSE Zn=x \An\Bn Adjust Bits/s Rate Control Modem Port Flow Control\Kn Same as 4.Default \Nn \Vn Protocol Result Code \Tn Inactivity TimerData Calling Tone \Xn XON/XOFF Pass ThroughV90=x V.90 Downstream Rate and Control Line-to-Line Loopback Enable/Disable Data CompressionAT Commands for Testing and Debugging Write to/Read from DSP RegisterTion failed Initial Transmit Carrier Rate 33600After initial negotiation Tion rate Final Transmit Carrier Rate 33600Rate Final Receive Carrier Rate 33600Registers Reference Range −32 Default Backspace Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Carriage return Units Range −127, Ascii decimal Default Line feed UnitsRange Default Unitsseconds Connection Completion Time-OutComma Dial Modifier Time S14 General Bit Mapped Options Status S10 Automatic Disconnect DelayS11 Dtmf Dialing Speed S12 Escape Guard TimeS24 Timer to Control Sleep Mode S21S22 S33 S28 Modulation Enable/DisableS30 Inactivity Timer S32Connection S37 Dial Line Rate defaultS38 56K Dial Line Rate default S36S40 S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S48 Lapm Error Control and Feature Negotiation defaultS92 S89 Timer to Control Sleep ModeS90 S91No Carrier Result Code Summary DescriptionPage FCC Regulations FCC Part 68 RequirementsDeclaration of Conformity Canadian Department Of Communications Cdoc