Actiontec electronic IS560LH user manual Canadian Department Of Communications Cdoc

Page 77

tion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inter- ference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter- ference to radio and television reception, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Canadian Department Of Communications (CDOC)

Requirements for End Users:

Notice: The Canadian Department of Communications label identifies certified equip- ment. This certification means the equipment meets certain telecommunications network requirements. The Department does not guarantee the equipment will op- erate to the user’s satisfaction.

Before installing this equipment users should ensure that connection to the line is allowed by the local telecommunications company. The equipment must also be in- stalled using an acceptable method of connection. In some cases, the company’s in- side wiring associated with a single line individual service may be extended by means of a telephone extension cord. Compliance with the above conditions may not pre- vent degradation of service in certain situations.

Repairs to certified equipment should be made by an authorized Canadian mainte- nance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

77

Page 76 Page 77
Image 77
Page 76 Page 77
Contents Internal Voice/Fax Windows Modem Table of Contents Introduction Do This First For Windows 95 and Windows 98 InstallationsWindows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box For Windows NT 4.0 Installation Proceed to the section titled Installing the ModemDevices Window Hardware Installation Installing The ModemInstalling The Modem Connecting Devices Connecting Devices To The ModemConfiguring Windows Page Page Finish Configuring Windows 95 OEM SR2Page Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page AT&F&C1&D2W2 Modem’s Voice FeaturesInit String Page Windows 95 and Windows TroubleshootingMore Info Panel Uninstalling the Modem Does Not InstallPage Page No Dialtone Error Common ProblemsPage Repeat Last Command AT CommandsAnswer Command +++ Escape sequenceThis command determines Ccitt vs. Bell standard Communication Standard SettingResult Codes Carrier ControlDnDial Hook Control Echo CommandOnline Data Character Echo Command Request ID Information Monitor Speaker VolumeThis command sets speaker volume to low, medium, or high Modulation Handshake This command turns the speaker on or offSelect Pulse Dialing Return On-line to Data ModeResult Code Control Select Tone DialingResult Code Option VnDCE Response FormatDial Tone Detect Extended Result CodesLong Space Disconnect Busy Tone DetectRecall Stored Profile Auto RetrainDTR Control Data Carrier Detect DCD ControlAuxiliary Relay option 22bis Guard Tone ControlThis Command is effective only for use in Japan Asynchronous Communications ModeLocal Flow Control Selection Pulse Dial Make-to-Break Ratio SelectionData Set Ready DSR Option This command selects DSR actionBelow is an example of a possible output This command is used to display the active profilesSSE \Bn Zn=x\An \Kn Adjust Bits/s Rate ControlModem Port Flow Control Same as 4.Default \Nn \Vn Protocol Result Code \Tn Inactivity TimerData Calling Tone \Xn XON/XOFF Pass ThroughV90=x V.90 Downstream Rate and Control AT Commands for Testing and Debugging Enable/Disable Data CompressionWrite to/Read from DSP Register Line-to-Line LoopbackAfter initial negotiation Tion failedInitial Transmit Carrier Rate 33600 Rate Final Transmit Carrier Rate 33600Final Receive Carrier Rate 33600 Tion rateRegisters Reference Range −127, Ascii decimal Default Carriage return Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Line feed Units Range −32 Default Backspace UnitsComma Dial Modifier Time Range Default UnitssecondsConnection Completion Time-Out S11 Dtmf Dialing Speed S10 Automatic Disconnect DelayS12 Escape Guard Time S14 General Bit Mapped Options StatusS22 S24 Timer to Control Sleep ModeS21 S30 Inactivity Timer S28 Modulation Enable/DisableS32 S33S38 56K Dial Line Rate default S37 Dial Line Rate defaultS36 ConnectionS43 Auto Mode default 1, range S42 Auto Rate default 1, rangeS48 Lapm Error Control and Feature Negotiation default S40S90 S89 Timer to Control Sleep ModeS91 S92No Carrier Result Code Summary DescriptionPage Declaration of Conformity FCC RegulationsFCC Part 68 Requirements Canadian Department Of Communications Cdoc
Top Page Image Contents