Actiontec electronic IS560LH user manual Online Data Character Echo Command, Hook Control

Page 42

En	Echo Command

This command controls whether or not the characters entered from your computer keyboard are echoed back to your monitor while the modem is in command mode.

	Command		Effect

	E0		Disables echo to the computer.

	E1		Enables echo to the computer (default).

Result Codes:

	OK	n = 0, 1

	ERROR	Otherwise

Fn		Online Data Character Echo Command

This command determines if the modem will echo data from the DTE. This modem does not support the F0 version of the command. However, the modem will accept F1, which may be issued by older communication software, to assure backward com- patibility.

	Command		Effect

	F0		Online data character echo enabled (Not supported,
	F0		will return ERROR).
			will return ERROR).

	F1		Online character echo disabled.

Result Codes:

	OK	n = 1

	ERROR	Otherwise

Hn		Hook Control

This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy.

Command	Effect

H0	Modem goes on-hook (default).

H1	Modem goes off-hook.

42

Image 42

Contents Internal Voice/Fax Windows Modem Table of Contents Introduction For Windows 95 and Windows 98 Installations Do This FirstWindows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box Proceed to the section titled Installing the Modem For Windows NT 4.0 InstallationDevices Window Installing The Modem Hardware InstallationInstalling The Modem Connecting Devices To The Modem Connecting DevicesConfiguring Windows Page Page Configuring Windows 95 OEM SR2 FinishPage Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Modem’s Voice Features Init StringAT&F&C1&D2W2 Page Troubleshooting Windows 95 and WindowsMore Info Panel Does Not Install Uninstalling the ModemPage Page Common Problems No Dialtone ErrorPage Answer Command AT CommandsRepeat Last Command +++ Escape sequenceResult Codes Communication Standard SettingThis command determines Ccitt vs. Bell standard Carrier ControlDnDial Echo Command Online Data Character Echo CommandHook Control Monitor Speaker Volume This command sets speaker volume to low, medium, or highRequest ID Information This command turns the speaker on or off Modulation HandshakeResult Code Control Return On-line to Data ModeSelect Pulse Dialing Select Tone DialingVnDCE Response Format Result Code OptionExtended Result Codes Dial Tone DetectRecall Stored Profile Busy Tone DetectLong Space Disconnect Auto RetrainData Carrier Detect DCD Control DTR Control22bis Guard Tone Control Auxiliary Relay optionLocal Flow Control Selection Asynchronous Communications ModeThis Command is effective only for use in Japan Pulse Dial Make-to-Break Ratio SelectionThis command selects DSR action Data Set Ready DSR OptionThis command is used to display the active profiles Below is an example of a possible outputSSE Zn=x \An\Bn Adjust Bits/s Rate Control Modem Port Flow Control\Kn Same as 4.Default \Nn \Tn Inactivity Timer \Vn Protocol Result Code\Xn XON/XOFF Pass Through Data Calling ToneV90=x V.90 Downstream Rate and Control Write to/Read from DSP Register Enable/Disable Data CompressionAT Commands for Testing and Debugging Line-to-Line LoopbackTion failed Initial Transmit Carrier Rate 33600After initial negotiation Final Receive Carrier Rate 33600 Final Transmit Carrier Rate 33600Rate Tion rateRegisters Reference Range −127, Ascii decimal Default Line feed Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Carriage return Units Range −32 Default Backspace UnitsRange Default Unitsseconds Connection Completion Time-OutComma Dial Modifier Time S12 Escape Guard Time S10 Automatic Disconnect DelayS11 Dtmf Dialing Speed S14 General Bit Mapped Options StatusS24 Timer to Control Sleep Mode S21S22 S32 S28 Modulation Enable/DisableS30 Inactivity Timer S33S36 S37 Dial Line Rate defaultS38 56K Dial Line Rate default ConnectionS48 Lapm Error Control and Feature Negotiation default S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S40S91 S89 Timer to Control Sleep ModeS90 S92Result Code Summary Description No CarrierPage FCC Regulations FCC Part 68 RequirementsDeclaration of Conformity Canadian Department Of Communications Cdoc