Actiontec electronic IS560LH user manual Xn XON/XOFF Pass Through, Data Calling Tone

Page 60

Result Codes:

	OK	n = 0, 1, 2

	ERROR	Otherwise

\Xn		XON/XOFF Pass Through

	Command		Effect

	\X0		Modem processes XON/XOFF flow control characters
	\X0		locally (default)
			locally (default)

	\X1		Modem processes and pass XON/XOFF flow control
	\X1		characters
			characters

Result Codes:

	OK	n = 0, 1

	ERROR	Otherwise

-Cn		Data Calling Tone

Data Calling Tone is a tone of certain frequency and cadence as specified in V.25 which allows remote Data/FAX/Voice discrimination. The frequency is 1300 Hz with a cadence of .5 s on and 2 s off.

	Command	Effect

	\X0	Modem processes XON/XOFF flow control characters
	\X0	locally (default)
		locally (default)

	\X1	Modem processes and pass XON/XOFF flow control
	\X1	characters
		characters

Result Codes:

OK

n = 0, 1

ERROR Otherwise

60

Image 60

Contents Internal Voice/Fax Windows Modem Table of Contents Introduction For Windows 95 and Windows 98 Installations Do This FirstWindows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box Proceed to the section titled Installing the Modem For Windows NT 4.0 InstallationDevices Window Installing The Modem Hardware InstallationInstalling The Modem Connecting Devices To The Modem Connecting DevicesConfiguring Windows Page Page Configuring Windows 95 OEM SR2 FinishPage Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Modem’s Voice Features Init StringAT&F&C1&D2W2 Page Troubleshooting Windows 95 and WindowsMore Info Panel Does Not Install Uninstalling the ModemPage Page Common Problems No Dialtone ErrorPage AT Commands Repeat Last CommandAnswer Command +++ Escape sequenceCommunication Standard Setting This command determines Ccitt vs. Bell standardResult Codes Carrier ControlDnDial Echo Command Online Data Character Echo CommandHook Control Monitor Speaker Volume This command sets speaker volume to low, medium, or highRequest ID Information This command turns the speaker on or off Modulation HandshakeReturn On-line to Data Mode Select Pulse DialingResult Code Control Select Tone DialingVnDCE Response Format Result Code OptionExtended Result Codes Dial Tone DetectBusy Tone Detect Long Space DisconnectRecall Stored Profile Auto RetrainData Carrier Detect DCD Control DTR Control22bis Guard Tone Control Auxiliary Relay optionAsynchronous Communications Mode This Command is effective only for use in JapanLocal Flow Control Selection Pulse Dial Make-to-Break Ratio SelectionThis command selects DSR action Data Set Ready DSR OptionThis command is used to display the active profiles Below is an example of a possible outputSSE Zn=x \An\Bn Adjust Bits/s Rate Control Modem Port Flow Control\Kn Same as 4.Default \Nn \Tn Inactivity Timer \Vn Protocol Result Code\Xn XON/XOFF Pass Through Data Calling ToneV90=x V.90 Downstream Rate and Control Enable/Disable Data Compression AT Commands for Testing and DebuggingWrite to/Read from DSP Register Line-to-Line LoopbackTion failed Initial Transmit Carrier Rate 33600After initial negotiation Final Transmit Carrier Rate 33600 RateFinal Receive Carrier Rate 33600 Tion rateRegisters Reference Range 0−255 Default UnitsASCII Range −127, Ascii decimal Default Carriage return UnitsRange −127, Ascii decimal Default Line feed Units Range −32 Default Backspace UnitsRange Default Unitsseconds Connection Completion Time-OutComma Dial Modifier Time S10 Automatic Disconnect Delay S11 Dtmf Dialing SpeedS12 Escape Guard Time S14 General Bit Mapped Options StatusS24 Timer to Control Sleep Mode S21S22 S28 Modulation Enable/Disable S30 Inactivity TimerS32 S33S37 Dial Line Rate default S38 56K Dial Line Rate defaultS36 ConnectionS42 Auto Rate default 1, range S43 Auto Mode default 1, rangeS48 Lapm Error Control and Feature Negotiation default S40S89 Timer to Control Sleep Mode S90S91 S92Result Code Summary Description No CarrierPage FCC Regulations FCC Part 68 RequirementsDeclaration of Conformity Canadian Department Of Communications Cdoc