Agilent Technologies E6701A manual Verify that Your Device Will Perform an Attach

Page 15

Verify that Your Device Will Perform an Attach

If necessary, follow the manufacturer’s instructions to install the SIM into the device.

1.1.Turn on the phone or wireless appliance.

Motorola Timeport phone example:

The device should indicate service signal-strength bars (in the upper left corner of the display) within about 1 minute.

It should also indicate the numbers “001-01” in the center of the display (this is the default test network number stored in the Test Set).

1.2.On the Test Set, in the bottom center of the display, the Active Cell box should show: Attached.

1.3.If the Active Cell box does not show service, verify that the Cell Band or Broadcast Channel for the test set matches the settings of the wireless device. Change as necessary.

Motorola Timeport Example:

a.Press the phone’s Menu key briefly.

b.Scroll to Network Selection with the up/down arrow key.

c.Press OK key to View Options?

d.The phone should display Change Band.

e.Press OK to View Options?.

f.Scroll to Change to 900/1800.

g.To choose the option, press OK to Select?

1.4.If the phone still doesn’t show service, look in Appendix B, Troubleshooting.

Set Up Your Wireless Device

These example instructions were written for a Motorola Timeport260 Series GPRS Mobile Phone. Other devices will require similar setups.

Note: Check the IP Address of the device whenever you turn on the device. Some devices reset this address.

Set the Device’s IP Address

1.After the phone is Attached, press the phone’s Menu key briefly.

2.When the display shows Access Internet / Select? press the OK key to select.

3.Now hold down the Menu key for about 3 seconds and release.

4.On the Browser Menu, scroll to 7 >Setup with the up/down arrow key.

5.Press the OK key.

If the phone hasn’t been setup yet, it will display a list of profiles such as profile1.

6.Use the up/down arrow key to highlight profile1 (or another unused profile location), or overwrite a previous profile.

7.Press the OK key.

8.Press the Menu (Edit) key.

a.On the profile1 menu, scroll to 1>WAP Settings

b.Press the OK key to Edit.

c.On the WAP Settings menu, scroll to 1>Primary IP:

d.Press the OK key to Edit

 Copyright 2002 Agilent Technologies.

10001810-E6701A Tutorial LAN Connection

All Rights Reserved.

Page 15 of 32

Rev. 1.2; Feb. 14, 2002

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Page Table of Contents Appendix B Troubleshooting Appendix C. Glossary Appendix a Installing a WAP Gateway into a PCIntroduction About This TutorialEquipment Required for this Tutorial Normal LAN Cable Quantity Setup Network Setup Test Set SetupLAN Addresses Set the Date and Time Optional Set the RF In/Out Amplitude OffsetSet the Cell and Call Parameters PC Setup Windows 98 and Dhcp AddressWindows 98 and Static Address Page Set up Network Windows 2000 and Dhcp AddressWindows 2000 and Static Address Determine PC IP address Verify PC Settings Motorola Timeport phone example Set Up Your Wireless DeviceOn the WAP Settings menu, scroll to 1Primary IP Verify that Your Device Will Perform an AttachSet WAPlite Gateway Address in Your Device On the WAP Settings menu, scroll to 2Primary PortSet the Device’s Primary Port Set Data Bearer to GprsSetup is now complete Product Feature Screen Image Capture Product Feature Protocol LoggingHere are some important points about the log data Save the Log to the PC View the log data on the PCView the saved log Log Data Using the Test Set’s Front PanelPinging the DUT the phone or wireless device Product Feature PingPinging an Alternate Device such as your PC on the LAN If your LAN does not use a firewall to access the Internet Product Feature Data ChannelMotorola Example Scroll to http//local/waplite.wmlMotorola Timeport Example Product Feature Additional Connection Parameters To load the WAPlite software on your PC Appendix a Installing a WAP Gateway into a PCInfinite WAPLite Gateway by Captaris Inc To download the WAPlite softwareAppendix B Troubleshooting If the wireless device will not attach, check thatIf Bler mode measurements have problems If Internet Explorer cannot access the 8960 Welcome Etsi Test Mode measurements have problemsPhone can’t access browse real Internet sites BER measurement errorsPhone won’t transmit IP datagrams in Data Channel functions Page Appendix C. Glossary
Top Page Image Contents