JVC BR-HD50 manual Playback, Video settings

Page 27

RECORDING

Recording with SERIAL REMOTE terminals

Recording can be turned ON/OFF with a serial remote controller or foot switch connected to the serial remote terminal located at the rear panel of BR-HD50.

 

SERIAL

REMOTE/LOCAL switch

REMOTE

PLAYBACK

Playback settings

Video settings

This unit plays back tapes recorded in HDV, DV,

Setting VIDEO Menu screen

or DVCAM format. (SP mode only)

„Selecting video format for HDMI OUT terminal and COMPONENT OUT terminal

z OUT FORMAT [60]/[50]

Select the playback image format to output

from the HDMI OUT terminal and the COMPO-

NENT OUT terminal. (Cross converter video)

[Settings [60]: NATIVE, 480I, 480P, 1080I, 720P]

• Serial remote controller

• Foot switch

Connection

The serial remote controller can be connected to the SERIAL REMOTE terminal located on the rear panel of BR-HD50.

Setting

„To use the SERIAL REMOTE terminal, set REMOTE SEL SER in the REMOTE [1/2] Menu screen to ON or LOC+REM. Then, set the REMOTE/LOCAL switch on the front panel accordingly.

zREMOTE SEL SER

ON : When the REMOTE/LOCAL switch is set to REMOTE, operations can be performed via the SERIAL REMOTE terminal.

LOC+REM : With the REMOTE/LOCAL switch is set either way, operations can be performed via the SERIAL REMOTE terminal. With this setting, the buttons and switches of the unit can be used too.

„Set FOOT SW in the REMOTE [2/2] Menu screen accord- ing to how the SERIAL REMOTE terminal is used.

OFF : Set to OFF when the serial remote controller is used. The footswitch cannot be used.

L EDGE : Recording and recording pause is switched at the LOW edge of the footswitch signal.

H EDGE : Recording and recording pause is switched at the HIGH edge of the footswitch signal.

L LEVEL : Recording is performed at the LOW edge and paused at the HIGH edge of the footswitch signal.

Operation

REMOTE [1/2] Menu screen

 

– – – R E MO T E [ 1 / 2 ] – – –

R E MO T E S E L 9 P

O N

R E MO T E S E L S E R

O N

R E M S E L H D V / D V

O N

L O C A L F U N C T I O N

S T P + E J T

P R E R O L L

7 S E C

N E X T

P A G E

 

P A G E

B A C K

 

 

 

 

Memo

zBesides recording, the serial remote controller can per- form other functions.

zIf the REMOTE SEL SER is set to ON, unit buttons that can be operated can be selected from LOCAL FUNCTION in the REMOTE [1/2] Menu screen.

REMOTE [2/2] Menu screen

– – – R E M O T E [ 2 / 2 ] – – –

R E M F F / R E W M O D E

F F / R E W

R E M S T O P S E L .

E E

P B S T A R T D E L A Y

0 F

S Y N C H R O N I Z A T I O N

O N

C O N T R O L L E R S E L

T Y P E 1

F O O T S W

L E D G E

P A G E B A C K

 

Foot switch

When playing back tapes recorded in HDV or DVCAM format, the front panel HDV or DVCAM indicator is lit.

„Selecting playback video format

Set whether to automatically detect the video format for playback, or to select a specific for- mat, using PB TAPE FORMAT on the SYS- TEM [2/2] Menu screen.

[Settings: AUTO, DV, HDV, DVCAM]

(Details: XPage 69)

„Setting IEEE1394 terminal output video format

Set the IEEE1394 terminal output video format to HDV or DV.

Set the IEEE1394 switch on the front panel, according to the playback video format.

HDV : Use this setting when the playback tape video format is HDV.

DV : Use this setting when the playback tape video format is DV or DVCAM.

Memo

zWhen playing back a tape recorded in HDV format, match the unit HD signal format (60Hz or 50Hz) to the playback signal format.

(XPage 40 “Selecting HD signal format”)

zPlayback output signal format: XPage 34

[Settings [50]: NATIVE, 576I, 576P, 1080I, 720P]

„Automatic selection of HDMI OUT ter- minal video output

zMONITOR SELECT

To automatically match the playback image format output from the HDMI OUT terminal to the video format of the connected display, set this menu item to HDMI[A].

[Settings: HDMI[A]/OUT FRMT]

„Screen display style for up/down-con- verter video

zDOWN CONV. MODE

The HDV signal is a wide-screen video signal. When playing a tape recorded in HDV format, the output from the LINE OUT terminal and Y/ C OUT terminal will be down-converted play- back images (480i/576i).

Set the style for displaying the down-con- verted playback image on a display with a 4:3 aspect ratio.

This will also apply to down-converted play- back images (480i/576i) output from the COM- PONENT OUT terminal.

[Settings: SQUEEZE/LETTER BOX/SIDECUT]

zUP CONV. MODE

Up-converts DV/DVCAM recorded tape play- back signals, and sets the video mode for out- put from the COMPONENT OUT terminal.

[Settings: FULL/SIDE P.]

Before using the foot switch, set BR-HD50 to the RECORDING or RECORDING PAUSE mode using the relevant buttons of the unit. (Only with L EDGE and H EDGE)

Memo

zThe foot switch can only be used to switch between RECORD- ING ON and OFF.

zThe foot switch can be operated regardless of the setting of the REMOTE/LOCAL switch.

Signal

H

Serial IN

terminal

L 400ms

Min

„Setting analog signal setup (U model only)

zSET UP [60]: DV

Set enabling or disabling the application of set- ups to analog video signals (composite, Y/C separate, and SD component).

VIDEO menu details: XPage 73 to 75

E-48

E-49

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Serial No LLT0088-001A For Customer UseBR-HD50HD Video Cassette Recorder BR-HD50UInformation for Canada Renseignement Pour Canada Important SafeguardsInformation RemarqueFor Continental EUROPE, ETC For U.K. only Power SystemFor Your Safety Please Read the Following Text Carefully Must be EarthedTable of Contents Introduction Remarks of usageCassette tape HDV and DV format „ Head cleaning Regular maintenanceCleaning tape „ Regular maintenanceNames and Functions of Parts 7COUNTER switch „ Dvcam indicator light„ 60 indicator light „ 50 indicator light„ SEARCH+/S button DHOLD button GCUE UP button EMENU button HSpecial functions/Setting buttonsFRESET button „ BLANK/P button3VIDEO Line OUT terminal BNC 0HDMI OUT Hdmi signal output termi- nal9CH2/4 Audio OUT terminal RCA 2VIDEO Y/C in terminal 4-PINESERIAL Remote terminal mini jack BDC power input terminalCDC power cord clamp DSIGNAL GND terminalON-SCREEN Display „ DV format„ HDV format Remaining tape VCR operation modeDate/time Counter displayDisplay Description Event/Alarm displayDisplay displayed during operation Description Display displayed for about 3 seconds Description„ Output signal „ Input signalConnection Connecting audio signals Attaching the supplied ferrite coreDigital input IEEE1394 terminal 6P To the DC cord. XPage „ Operate BR-HD50 with the wired remote controllerComponent OUT RECORDING/OUTPUT Signal FormatPreparation Turning on the powerTurning off the power „ Output terminal video/audio signal format during playbackEjecting the cassette tape Selecting the operating method main unit/remote controllerOperation Lock mode Loading the cassette tape„ Display Menu screen Setting date and timeSelecting date/time display On-screen status displayRecording Check settingsSetting the Menu screen Setting Menu screensTting related Menu screen Selecting input signalAdjusting audio recording level SettingsSource unit Recording index signalsPlayback Video settingsAudio settings Settings regarding playback functionFast forward/rewind Frame-advance playback Slow playback and Search mode„ In the Stop mode, press the Blank button „ Repeat Mode in the System 1/2 Menu screenIndex search Blank searchSearching cue-up points Changing cue-up pointsRegistering cue-up points Exiting the Multi Cue-up screen„ NDF/DF 60 U model only Time CodeTCG Select Regen Recording from preset dataTCG Select Preset „ Set the TC/UB/CLOCK 1/2 Menu as follows„ Remote 2/2 Menu screen Control with RS-422A Analog signalsControl with the IEEE1394 ter- minal Digital signals EditMenu screen on counter display „ Set BR-HD50 to the Stop or Still modeSetting the menus Menu ScreensTOP Menu screen System Menu screens„ System 1/2 Menu screens „ System 2/2 Menu Remote Menu screens Video Menu Screen Audio Menu ScreenDown Conv Hdmi ModeTest Signal OUT forTC/UB/CLOCK Menu screens „ TC/UB/CLOCK 1/2 Menu screen„ TC/UB/CLOCK 2/2 Menu screen „ Alarm display Displayed regardless of the Display mode OthersDisplay Menu screen „ Warning display Displayed regardless of the Display mode „ Set BR-HD50 to the Stop mode „ General „ Connectors„ Accessories „ External dimensions Unit mmImportant Safety Instructions „ AC adapter sectionSupplement
Top Page Image Contents