TIME CODE
Displaying the time code
This unit records or plays back the time code and user’s bit. Whether to record the user’s bit can be selected with
TIME CODE
Presetting the time code
Variable values can be set for the time code and the user’s bit for efficient material management and editing.
SET button
DISP/R button RESET button
TCG | : | Time code generator data |
TCR | : | Time code reader data |
DTCG : Input time code data from
| the IEEE1394 terminal |
UBG | : User’s bit generator data |
UBR | : User’s bit reader data |
Status display (Monitor)
D V 3 2 K C H – 1 / 2 | S P 6 0 M I N |
| |||||||
|
|
|
|
|
|
| |||
| W A R N I N G 7 0 0 1 |
|
| ||||||
| D R UM MO T O R F A I L U R E |
| Framing mode | ||||||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
| R E C | I N H I B I T |
|
|
| ||||
|
|
|
|
|
|
|
|
| (for NTSC only) |
|
|
|
|
|
|
|
|
| |
0 6 / 1 0 / 0 5 |
|
|
|
| S T A N D B Y | : (colon) : | |||
|
|
|
|
| |||||
|
|
|
|
|
|
| |||
1 0 : 2 0 : 0 0 |
|
|
| T C R 0 2 : 0 0 : 0 0 : 0 0 |
| ||||
Q button |
|
|
|
HOLD button | P button | S button | COUNTER switch |
DUBG : User’s bit input data from the IEEE1394 terminal
. (dot) : Drop frame |
Setting ...TC/UB/CLOCK [1/2] Menu screen
Set TCG SELECT to “PRESET”. |
TC/UB/CLOCK[1/2] Menu screen
– – – T C / U B / C L O C K [ 1 / 2 ] – – –
Time code/User’s bit display
During recording and stop mode: Data of time code generator
During playback | : Data recorded on the tape |
During DV input | : Data selected with TC DUPLI.: |
| DV in the TC/UB/CLOCK |
| Menu screen |
The time code advance mode is |
NDF/DF [60] (U model only) |
when emphasizing the frame count.
DROP : Enters
T C G S E L E C T | P R E S E T | |
N D F / D F [ 6 0 ] | D R O P | |
D F B I T [ 5 0 ] | O N | |
T C D U P L I . : D V | O F F | |
T C O F F S E T | O F F | |
N E X T | P A G E |
|
P A G E | B A C K |
|
To display the time code/ user’s bit, perform the fol- lowing settings.
•Set DISPLAY in the DISPLAY Menu screen to ON or AUTO. J The status is displayed on the monitor.
•Set TIME CODE in the DISPLAY Menu screen to ON.
JThe time code, user’s bit or CTL counter is displayed at the
counter display section of the status display.
•Select the counter display mode with the COUNTER switch on the front panel.
To display the time code, select TC. To display the user’s bit, select UB.
Checking the data of time code generator
When it is in the STOP mode, press the REC button and the data of the time code generator will be displayed while the button is held down.
DISPLAY Menu screen
| – – – D I S P L A Y – – – | |
D I S P L A Y | O N | |
C O U N T E R P O S I . | L O W E R - R | |
T I M E | C O D E | O N |
V T R | M O D E | O N |
T A P E R E M A I N | O N | |
T I M E / D A T E | D A T E + T M | |
A / V | I N F O . | O N |
D A T E S T Y L E | D D / M M / Y Y | |
T I M E S T Y L E | 2 4 H O U R | |
P A G E | B A C K |
|
The display position can be selected.
Operation ...Perform setting while checking the Counter display.
This section describes the setting of the time code. The setting of the user’s bit is the same. Values that can be used to configure the user’s bit are hexadecimal numeral from 0 - F.
1.Set the COUNTER switch to TC. (For user’s bit, set the switch to UB.)
2.In the STOP mode, press the HOLD button.
J The hour digit of the counter starts blinking.
3.Press the R or P button to change the value.
4.Press the S or Q button to move blinking to the next digit.
5.Press the R or P button to change the value of the blink- ing digit.
6.Repeat steps 4 and 5 to perform the necessary settings.
7.Press the SET button to confirm the setting value and blinking of the counter stops.
J The setting is preset to the time code generator.
Memo
zTo stop the setting, press the HOLD button to return to the normal screen.
zTo preset all digits to 0, press the RESET button when any of the digits is blinking.
zWhen the hour digit is blink- ing, the frame digit starts blinking when the Q button is pressed.
zIf a user’s bit is input with its all digits set as “F”,
COUNTER switch