Yamaha CRW2200S manual Setting the Jumper Switches, Jumper switches, Rear Panel

Page 28

SCSI Connection Set Up

Setting the Jumper Switches

8Before fitting the CRW2200S into the computer, you need to set up the drive using the jumper switches located at the rear of the unit. You’ll need to set the following:

➀SCSI ID number

➁ Parity check

➂ Termination

➃ Block size

To set each jumper switch, you have to bridge the two pins in the respective column of the grid with a plastic shunt. Shunts are already attached to the jumper switches in their default configurations.

Jumper switches

1 2 4

ID SELECT PARITY. TERMINATOR BLOCK SIZE

Rear Panel

Note

The plastic shunts actually contain metal for bridging the two pins of a jumper switch, creating an electrical connection between them when attached. When removed, the jumper switch is set to “OFF.” Store unused shunts in a safe place where they will not be lost.

Use a pair of long-nosed pliers to attach or detach the plastic shunts accordingly. Make sure that the computer is turned off beforehand.

20

Image 28

Contents Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents → E-IDE Atapi Connection Set Up P → Scsi Connection Set Up PScsi convertor Features of the CRW2200 drive IntroductionYamaha Buffer Underrun Protection Buffer Underrun DefinedIntroduction System Requirements Before UseThese are also required for Scsi connection Supported Discs CD-R discs*1CD-RW discs*2 High Speed CD-RW discs*3About CD-ROMs About Partial CAV Constant Angular VelocityAbout 10X-speed writing/rewriting of a High Speed CD-RW disc Serial Number Serial number Letters and 7 digitsFront and Rear of Unit Front PanelRear Panel with the Scsi Convertor ➀ Digital Audio OUT connector ➁ Analog Audio OUT connector➂ Jumper switch ➄ DC Input connectorScsi Connection Set Up ToolsPhillips Screwdriver Long-Nosed PliersCRW2200S Setup Flowchart Scsi Connection Set UpConnecting the CRW2200S Opening the ComputerShut down your computer and unplug it from the AC outlet Cover Front panelDischarge any static charge Connecting the analog audio cable Audio cable connectionConnect the audio cable to the CRW2200 drive. If necessary Left L Ground G Right R Audio cable To Sound cardConnecting the digital audio cable Ground G Signal D Digital audio cable To Sound cardInstalling the Scsi Convertor to the CRW2200 drive ScrewYellow wire DC InputJumper switches Setting the Jumper SwitchesRear Panel ➀ Scsi ID Number Scsi ID➁ Parity Check ➂ TerminationBlock size OFF Default Block size on Set to on when installing➃ Block Size WorkstationChoosing the Connection Method As a replacement driveCD-ROM drive Audio cable Pin IDE cable Pin power cable Installing the CRW2200SInch drive bay slot Front cover Colored line connector Scsi connector 50-pin Scsi flat cable MotherboardDigital audio cable Sound card SpdifTop Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on Configuring for the Operating System For Windows NTInstalling the CD Writing Software Install the CD writing softwareRemoving the Scsi convertor Removing the Scsi convertorAudio cable Pin Scsi flat cable Pin power cable Removing the Scsi convertorRemove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up CRW2200E Setup Flowchart IDE Atapi Connection Set UpConnecting the CRW2200E Choosing the Connection Method About IDE Typical IDE-type hardware installationSlave Motherboard Primary Master Secondary SlaveMaster Connecting examples Example-1 As secondary slave For supplemental driveIDE Atapi Connection Set Up About the Csel jumper switch Rear Panel Master Slave factory settingInstalling the CRW2200E As an supplemental driveConnect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Loading a Disc OperationEjecting a Disc Operation Ejecting a Disc in an EmergencyManual Eject hole Paper Clip Troubleshooting Yamaha CD-R/RW Drives web site URL EuropeTroubleshooting Disc keeps being ejected Properties setting of the CRW2200S Setting of the Windows Media PlayerBuffer Underrun error message is displayed Appendix Writing ModesDisc-at-Once DAO Track-at-Once TAOPacket Writing Session-at-Once SAOAppendix About firmware URL for Yamaha CD-R/RW Drives web sites EuropeLED Indicator Messages Status Ndicator essages LED olorCD-RW CRW2200 drive CRW2200 series complies with the following specifications Symbols IndexPhillips Screwdriver 12, 32 EUROPE, Eastern Europe Russia