Yamaha CRW2200S manual Top DC Input connector Bottom Pin power cable

Page 54

E-IDE (ATAPI) Connection Set Up

10Connect a 4-pin power cable to the power supply connector of the CRW2200E marked “DC INPUT.”

Top

DC INPUT connector

Bottom	4-pin power cable

Notes

•There may be more than one 4-pin power cable available. Any one may be used.

•These connectors are D-shaped, so you can only connect the power cables in the correct orientation. Do not apply excessive force when making this connection.

11Tighten the four fastening screws on the side of the unit securely using a phillips screwdriver. (→P. 28 step 15)

12Attach the outer casing and all cables and peripheral devices of the computer and any screws that were removed. (→P. 29 step 16)

13Reconnect the computer to the AC outlet and turn it on. (→P. 29 step 17)

When you turn on the computer, make sure the LED on the panel of the

CRW2200E blinks in green, which indicates that it is reading disc information. (→P. 60)

46

Image 54

Contents Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents → Scsi Connection Set Up P → E-IDE Atapi Connection Set Up PScsi convertor Features of the CRW2200 drive IntroductionBuffer Underrun Defined Yamaha Buffer Underrun ProtectionIntroduction Before Use System RequirementsThese are also required for Scsi connection CD-RW discs*2 Supported DiscsCD-R discs*1 High Speed CD-RW discs*3About CD-ROMs About Partial CAV Constant Angular VelocityAbout 10X-speed writing/rewriting of a High Speed CD-RW disc Serial Number Serial number Letters and 7 digitsFront and Rear of Unit Front PanelRear Panel with the Scsi Convertor ➂ Jumper switch ➀ Digital Audio OUT connector➁ Analog Audio OUT connector ➄ DC Input connectorPhillips Screwdriver Scsi Connection Set UpTools Long-Nosed PliersCRW2200S Setup Flowchart Scsi Connection Set UpShut down your computer and unplug it from the AC outlet Connecting the CRW2200SOpening the Computer Cover Front panelDischarge any static charge Connect the audio cable to the CRW2200 drive. If necessary Connecting the analog audio cableAudio cable connection Left L Ground G Right R Audio cable To Sound cardConnecting the digital audio cable Ground G Signal D Digital audio cable To Sound cardInstalling the Scsi Convertor to the CRW2200 drive ScrewYellow wire DC InputSetting the Jumper Switches Jumper switchesRear Panel ➀ Scsi ID Number Scsi ID➁ Parity Check ➂ Termination➃ Block Size Block size OFF Default Block size onSet to on when installing WorkstationAs a replacement drive Choosing the Connection MethodCD-ROM drive Installing the CRW2200S Audio cable Pin IDE cable Pin power cableInch drive bay slot Front cover Colored line connector Scsi connector 50-pin Scsi flat cable MotherboardDigital audio cable Sound card SpdifTop Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on Configuring for the Operating System For Windows NTInstalling the CD Writing Software Install the CD writing softwareRemoving the Scsi convertor Removing the Scsi convertorAudio cable Pin Scsi flat cable Pin power cable Removing the Scsi convertorRemove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up CRW2200E Setup Flowchart IDE Atapi Connection Set UpConnecting the CRW2200E Choosing the Connection Method Typical IDE-type hardware installation About IDESlave Motherboard Primary Master Secondary SlaveMaster Connecting examples Example-1 As secondary slave For supplemental driveIDE Atapi Connection Set Up About the Csel jumper switch Rear Panel Master Slave factory settingInstalling the CRW2200E As an supplemental driveConnect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Operation Loading a DiscEjecting a Disc Ejecting a Disc in an Emergency OperationManual Eject hole Paper Clip Troubleshooting Yamaha CD-R/RW Drives web site URL EuropeTroubleshooting Disc keeps being ejected Properties setting of the CRW2200S Setting of the Windows Media PlayerBuffer Underrun error message is displayed Disc-at-Once DAO AppendixWriting Modes Track-at-Once TAOSession-at-Once SAO Packet WritingAppendix About firmware URL for Yamaha CD-R/RW Drives web sites EuropeLED Indicator Messages Status Ndicator essages LED olorCD-RW CRW2200 drive CRW2200 series complies with the following specifications Symbols IndexPhillips Screwdriver 12, 32 EUROPE, Eastern Europe Russia