Yamaha CRW2200S manual Disc keeps being ejected

Page 62

Troubleshooting

●Check to see if there are any problems with other IDE devices. Some problems may occur in a multiple-IDE device system due to incompatibilities between the IDE devices and the computer, device drivers, data transfer speed, or other reasons. Make sure that the CRW2200E is recognized by the computer by temporarily removing other IDE devices from the system.

●Are the pins and holes on the IDE connectors straight and not deformed? Check the connectors. (→P. 43)

●Are your IDE devices connected correctly?

If only one device is connected to one IDE cable, check that the setting of the device is MASTER or CSEL. When you connect two IDE devices to one IDE

cable, be sure to assign each as MASTER or SLAVE respectively. If the setting of the CRW2200E is CSEL, change the setting to MASTER or SLAVE. (→P. 42)

●Is the CRW2200 drive connected to a high-speed device, such as a hard disk drive?

If you connect two devices with quite different speeds using the same cable, operation may become unstable.

●To write to CD-R/RW discs, your CD writing software must support the CRW2200E.

To find out if it does, contact the manufacturer of your CD writing software.

The disc tray does not open.

●Is the CRW2200 drive turned on?

The LED on the front panel of the CRW2200 drive lights up.

●Some CD writing software will lock the disc tray once loaded.

In this case, use the eject command from within the software. Refer also to the documentation that came with the software.

●Disconnect the SCSI or IDE cable from the CRW2200 drive. Turn on the computer, and press the eject button.

The disc keeps being ejected.

●Has the disc been placed on the disc tray correctly?

The drive does not operate correctly.

●Is the disc compatible with the CRW2200 drive? (→P. 60) Blank discs cannot be played.

●Is there dust on the disc tray or on the disc itself?

●Does the computer have a sufficient power supply?

The CRW2200 drive’s power consumption is 12W with a SCSI connection and 11W with a ATAPI connection (when reading and writing).

●Does your computer have several different CD writing software applications installed?

If you use two or more CD writing software application simultaneously, the behavior of the drive may become unpredictable.

54

Image 62

Contents Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents Scsi convertor → Scsi Connection Set Up P→ E-IDE Atapi Connection Set Up P Features of the CRW2200 drive IntroductionIntroduction Buffer Underrun DefinedYamaha Buffer Underrun Protection These are also required for Scsi connection Before UseSystem Requirements CD-RW discs*2 Supported DiscsCD-R discs*1 High Speed CD-RW discs*3About CD-ROMs About Partial CAV Constant Angular VelocityAbout 10X-speed writing/rewriting of a High Speed CD-RW disc Serial Number Serial number Letters and 7 digitsFront and Rear of Unit Front PanelRear Panel with the Scsi Convertor ➂ Jumper switch ➀ Digital Audio OUT connector➁ Analog Audio OUT connector ➄ DC Input connectorPhillips Screwdriver Scsi Connection Set UpTools Long-Nosed PliersCRW2200S Setup Flowchart Scsi Connection Set UpShut down your computer and unplug it from the AC outlet Connecting the CRW2200SOpening the Computer Cover Front panelDischarge any static charge Connect the audio cable to the CRW2200 drive. If necessary Connecting the analog audio cableAudio cable connection Left L Ground G Right R Audio cable To Sound cardConnecting the digital audio cable Ground G Signal D Digital audio cable To Sound cardInstalling the Scsi Convertor to the CRW2200 drive ScrewYellow wire DC InputRear Panel Setting the Jumper SwitchesJumper switches ➀ Scsi ID Number Scsi ID➁ Parity Check ➂ Termination➃ Block Size Block size OFF Default Block size onSet to on when installing WorkstationCD-ROM drive As a replacement driveChoosing the Connection Method Inch drive bay slot Front cover Installing the CRW2200SAudio cable Pin IDE cable Pin power cable Colored line connector Scsi connector 50-pin Scsi flat cable MotherboardDigital audio cable Sound card SpdifTop Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on Configuring for the Operating System For Windows NTInstalling the CD Writing Software Install the CD writing softwareRemoving the Scsi convertor Removing the Scsi convertorAudio cable Pin Scsi flat cable Pin power cable Removing the Scsi convertorRemove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up CRW2200E Setup Flowchart IDE Atapi Connection Set UpConnecting the CRW2200E Choosing the Connection Method Slave Motherboard Primary Master Secondary SlaveMaster Typical IDE-type hardware installationAbout IDE Connecting examples Example-1 As secondary slave For supplemental driveIDE Atapi Connection Set Up About the Csel jumper switch Rear Panel Master Slave factory settingInstalling the CRW2200E As an supplemental driveConnect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Ejecting a Disc OperationLoading a Disc Manual Eject hole Paper Clip Ejecting a Disc in an EmergencyOperation Troubleshooting Yamaha CD-R/RW Drives web site URL EuropeTroubleshooting Disc keeps being ejected Properties setting of the CRW2200S Setting of the Windows Media PlayerBuffer Underrun error message is displayed Disc-at-Once DAO AppendixWriting Modes Track-at-Once TAOAppendix Session-at-Once SAOPacket Writing About firmware URL for Yamaha CD-R/RW Drives web sites EuropeLED Indicator Messages Status Ndicator essages LED olorCD-RW CRW2200 drive CRW2200 series complies with the following specifications Symbols IndexPhillips Screwdriver 12, 32 EUROPE, Eastern Europe Russia