Yamaha CRW2200S manual Cd-Rw

Page 69

Appendix

Writing Methods	Disc-at-Once (DAO)
	Session-at-Once (SAO)
	Track-at-Once (TAO)
	Packet Writing

Writing/Reading Speed	Writing CD-R	1X, 2X, 4X, 8X, 12X (CLV),
		16X (12X – 16X Partial CAV)
		20X (12X – 20X Partial CAV)
	CD-RW	2X, 4X, 8X, 10X (CLV)
		4X – 10X Full CAV

	Reading	40X (max.) Full CAV
		Note)	• DATA: 40X (max.)
			• CD-DA: 40X (max.) in audio extraction
			• CD-DA: 1X only in audio play
			• Video CD: 10X (max.)
			• Session closed disc: 40X (max.)
			• Session unclosed disc: 12X (max.)

	CD-R	1X, 2X, 4X, 8X, 12X, 16X (12X – 16X Partial CAV),
		20X (12X – 20X Partial CAV) writing:
		CD-R discs specified in Orange Book Part II Ver. 3.1.
		Note)	For 8X or faster writing, use CD-R discs matched their
			respective writing speeds
	CD-RW	• 2X writing/rewriting: Rewritable discs specified in Orange
		Book Part III Volume 1 Version 1.0.
		• 2X or 4X writing/rewriting: Rewritable discs specified in
		Orange Book Part III Volume 1 Version 2.0.
		• 4X, 8X, 10X (CLV), 4X – 10X Full CAV writing/rewriting:
		Rewritable discs specified in Orange Book Part III Volume 2
		Version 1.0.

Data Capacity		700MB (79 min.)
		650MB (74 min.)
		550MB (63 min.)

Data Transfer Rate (Mode 1)		1X:	150KB/sec.	16X: 2,400KB/sec.
		2X:	300KB/sec.	20X: 3,000KB/sec.
		4X:	600KB/sec.	24X: 3,600KB/sec.
		8X: 1,200KB/sec.		32X: 4,800KB/sec.
		10X: 1,500KB/sec.		40X: 6,000KB/sec.
		12X: 1,800KB/sec.

Burst Transfer Rate		SCSI connection

•5MB/sec. (max, asynchronous)

•20MB/sec. (max, synchronous)

	E-IDE (ATAPI) connection
	• Programmed I/O mode 4:	16.7MB/sec.
	• Multiword DMA mode 2:	16.7MB/sec.
	• Ultra DMA mode 2 (Ultra DMA/33): 33.3MB/sec.

Data Buffer Size	8MB (3,224 sectors)

61

Image 69

Contents Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents → Scsi Connection Set Up P → E-IDE Atapi Connection Set Up PScsi convertor Introduction Features of the CRW2200 driveBuffer Underrun Defined Yamaha Buffer Underrun ProtectionIntroduction Before Use System RequirementsThese are also required for Scsi connection CD-R discs*1 Supported DiscsCD-RW discs*2 High Speed CD-RW discs*3About Partial CAV Constant Angular Velocity About CD-ROMsAbout 10X-speed writing/rewriting of a High Speed CD-RW disc Serial number Letters and 7 digits Serial NumberFront Panel Front and Rear of UnitRear Panel with the Scsi Convertor ➁ Analog Audio OUT connector ➀ Digital Audio OUT connector➂ Jumper switch ➄ DC Input connectorTools Scsi Connection Set UpPhillips Screwdriver Long-Nosed PliersScsi Connection Set Up CRW2200S Setup FlowchartOpening the Computer Connecting the CRW2200SShut down your computer and unplug it from the AC outlet Cover Front panelDischarge any static charge Audio cable connection Connecting the analog audio cableConnect the audio cable to the CRW2200 drive. If necessary Left L Ground G Right R Audio cable To Sound cardGround G Signal D Digital audio cable To Sound card Connecting the digital audio cableScrew Installing the Scsi Convertor to the CRW2200 driveDC Input Yellow wireSetting the Jumper Switches Jumper switchesRear Panel Scsi ID ➀ Scsi ID Number➂ Termination ➁ Parity CheckSet to on when installing Block size OFF Default Block size on➃ Block Size WorkstationAs a replacement drive Choosing the Connection MethodCD-ROM drive Installing the CRW2200S Audio cable Pin IDE cable Pin power cableInch drive bay slot Front cover Motherboard Colored line connector Scsi connector 50-pin Scsi flat cableSpdif Digital audio cable Sound cardTop Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on For Windows NT Configuring for the Operating SystemInstall the CD writing software Installing the CD Writing SoftwareRemoving the Scsi convertor Removing the Scsi convertorRemoving the Scsi convertor Audio cable Pin Scsi flat cable Pin power cableRemove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up IDE Atapi Connection Set Up CRW2200E Setup FlowchartConnecting the CRW2200E Choosing the Connection Method Typical IDE-type hardware installation About IDESlave Motherboard Primary Master Secondary SlaveMaster Example-1 As secondary slave For supplemental drive Connecting examplesIDE Atapi Connection Set Up Rear Panel Master Slave factory setting About the Csel jumper switchAs an supplemental drive Installing the CRW2200EConnect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Operation Loading a DiscEjecting a Disc Ejecting a Disc in an Emergency OperationManual Eject hole Paper Clip Yamaha CD-R/RW Drives web site URL Europe TroubleshootingTroubleshooting Disc keeps being ejected Setting of the Windows Media Player Properties setting of the CRW2200SBuffer Underrun error message is displayed Writing Modes AppendixDisc-at-Once DAO Track-at-Once TAOSession-at-Once SAO Packet WritingAppendix URL for Yamaha CD-R/RW Drives web sites Europe About firmwareStatus Ndicator essages LED olor LED Indicator MessagesCD-RW CRW2200 drive CRW2200 series complies with the following specifications Index SymbolsPhillips Screwdriver 12, 32 Russia EUROPE, Eastern Europe