Yamaha CRW2200S manual Configuring for the Operating System, For Windows NT

Page 38

SCSI Connection Set Up

Configuring for the Operating System

18After the computer’s operating system (Windows 95/98/98 Second Edition/Me) has loaded, open “Control Panel” and double-click on the “System” icon. Select the “Device Manager” tab and double-click on “CDROM.” If the drive has been correctly installed, it should be listed as shown below. Similarly, double-click on “SCSI controllers” and the SCSI card should be listed as shown below if it has been properly installed.

* This is a screen shown in the Windows Me environment.

For Windows NT

You can verify by opening “Control Panel,” double-clicking on “SCSI Adapter” and clicking on the “Devices” tab.

For Windows 2000 Professional

You can verify by opening “Control Panel,” double-clicking on “System,” selecting the “Hardware” tab, and clicking on the “Device Manager” button in “System Properties.”

Notes

For details about how to use the operating system, refer to the documentation that came with it.

If there is a or mark etc. next to the icon for the CRW2200S or the SCSI card, this means that it has not been installed correctly.

30

Image 38
Contents Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents Scsi convertor → Scsi Connection Set Up P→ E-IDE Atapi Connection Set Up P Features of the CRW2200 drive IntroductionIntroduction Buffer Underrun DefinedYamaha Buffer Underrun Protection These are also required for Scsi connection Before UseSystem Requirements CD-RW discs*2 Supported DiscsCD-R discs*1 High Speed CD-RW discs*3About CD-ROMs About Partial CAV Constant Angular VelocityAbout 10X-speed writing/rewriting of a High Speed CD-RW disc Serial Number Serial number Letters and 7 digitsFront and Rear of Unit Front PanelRear Panel with the Scsi Convertor ➂ Jumper switch ➀ Digital Audio OUT connector➁ Analog Audio OUT connector ➄ DC Input connectorPhillips Screwdriver Scsi Connection Set UpTools Long-Nosed PliersCRW2200S Setup Flowchart Scsi Connection Set UpShut down your computer and unplug it from the AC outlet Connecting the CRW2200SOpening the Computer Cover Front panelDischarge any static charge Connect the audio cable to the CRW2200 drive. If necessary Connecting the analog audio cableAudio cable connection Left L Ground G Right R Audio cable To Sound cardConnecting the digital audio cable Ground G Signal D Digital audio cable To Sound cardInstalling the Scsi Convertor to the CRW2200 drive ScrewYellow wire DC InputRear Panel Setting the Jumper SwitchesJumper switches ➀ Scsi ID Number Scsi ID➁ Parity Check ➂ Termination➃ Block Size Block size OFF Default Block size onSet to on when installing WorkstationCD-ROM drive As a replacement driveChoosing the Connection Method Inch drive bay slot Front cover Installing the CRW2200SAudio cable Pin IDE cable Pin power cable Colored line connector Scsi connector 50-pin Scsi flat cable MotherboardDigital audio cable Sound card SpdifTop Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on Configuring for the Operating System For Windows NTInstalling the CD Writing Software Install the CD writing softwareRemoving the Scsi convertor Removing the Scsi convertorAudio cable Pin Scsi flat cable Pin power cable Removing the Scsi convertorRemove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up CRW2200E Setup Flowchart IDE Atapi Connection Set UpConnecting the CRW2200E Choosing the Connection Method Slave Motherboard Primary Master Secondary SlaveMaster Typical IDE-type hardware installationAbout IDE Connecting examples Example-1 As secondary slave For supplemental driveIDE Atapi Connection Set Up About the Csel jumper switch Rear Panel Master Slave factory settingInstalling the CRW2200E As an supplemental driveConnect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Ejecting a Disc OperationLoading a Disc Manual Eject hole Paper Clip Ejecting a Disc in an EmergencyOperation Troubleshooting Yamaha CD-R/RW Drives web site URL EuropeTroubleshooting Disc keeps being ejected Properties setting of the CRW2200S Setting of the Windows Media PlayerBuffer Underrun error message is displayed Disc-at-Once DAO AppendixWriting Modes Track-at-Once TAOAppendix Session-at-Once SAOPacket Writing About firmware URL for Yamaha CD-R/RW Drives web sites EuropeLED Indicator Messages Status Ndicator essages LED olorCD-RW CRW2200 drive CRW2200 series complies with the following specifications Symbols IndexPhillips Screwdriver 12, 32 EUROPE, Eastern Europe Russia