Yamaha CRW2200S manual Configuring for the Operating System

Page 55

E-IDE (ATAPI) Connection Set Up

Configuring for the Operating System

14When using Windows 95/98/98 Second Edition/Me, after the computer’s operating system has loaded, open “Control Panel” and double-click on the “System” icon. Select the “Device Manager” tab and double-click on “CDROM.” If the drive has been correctly installed, it should be listed as shown in the figure below.

* This is a screen shown in the Windows Me environment.

For Windows NT

You can verify by opening “Control Panel,” double-clicking on “SCSI Adapter” and clicking on the “Devices” tab.

For Windows 2000 Professional

You can verify by opening “Control Panel,” double-clicking on “System,” selecting the “Hardware” tab, and clicking on the “Device Manager” button in “System Properties.”

Notes

•For details about how to use the operating system, refer to the documentation that came with it.

•If there is an or mark, etc., next to the icon for the CRW2200E, this means that it has not been installed correctly.

47

Image 55

Contents Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents → E-IDE Atapi Connection Set Up P → Scsi Connection Set Up PScsi convertor Introduction Features of the CRW2200 driveYamaha Buffer Underrun Protection Buffer Underrun DefinedIntroduction System Requirements Before UseThese are also required for Scsi connection High Speed CD-RW discs*3 Supported DiscsCD-R discs*1 CD-RW discs*2About Partial CAV Constant Angular Velocity About CD-ROMsAbout 10X-speed writing/rewriting of a High Speed CD-RW disc Serial number Letters and 7 digits Serial NumberFront Panel Front and Rear of UnitRear Panel with the Scsi Convertor ➄ DC Input connector ➀ Digital Audio OUT connector➁ Analog Audio OUT connector ➂ Jumper switchLong-Nosed Pliers Scsi Connection Set UpTools Phillips ScrewdriverScsi Connection Set Up CRW2200S Setup FlowchartCover Front panel Connecting the CRW2200SOpening the Computer Shut down your computer and unplug it from the AC outletDischarge any static charge Left L Ground G Right R Audio cable To Sound card Connecting the analog audio cableAudio cable connection Connect the audio cable to the CRW2200 drive. If necessaryGround G Signal D Digital audio cable To Sound card Connecting the digital audio cableScrew Installing the Scsi Convertor to the CRW2200 driveDC Input Yellow wireJumper switches Setting the Jumper SwitchesRear Panel Scsi ID ➀ Scsi ID Number➂ Termination ➁ Parity CheckWorkstation Block size OFF Default Block size onSet to on when installing ➃ Block SizeChoosing the Connection Method As a replacement driveCD-ROM drive Audio cable Pin IDE cable Pin power cable Installing the CRW2200SInch drive bay slot Front cover Motherboard Colored line connector Scsi connector 50-pin Scsi flat cableSpdif Digital audio cable Sound cardTop Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on For Windows NT Configuring for the Operating SystemInstall the CD writing software Installing the CD Writing SoftwareRemoving the Scsi convertor Removing the Scsi convertorRemoving the Scsi convertor Audio cable Pin Scsi flat cable Pin power cableRemove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up IDE Atapi Connection Set Up CRW2200E Setup FlowchartConnecting the CRW2200E Choosing the Connection Method About IDE Typical IDE-type hardware installationSlave Motherboard Primary Master Secondary SlaveMaster Example-1 As secondary slave For supplemental drive Connecting examplesIDE Atapi Connection Set Up Rear Panel Master Slave factory setting About the Csel jumper switchAs an supplemental drive Installing the CRW2200EConnect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Loading a Disc OperationEjecting a Disc Operation Ejecting a Disc in an EmergencyManual Eject hole Paper Clip Yamaha CD-R/RW Drives web site URL Europe TroubleshootingTroubleshooting Disc keeps being ejected Setting of the Windows Media Player Properties setting of the CRW2200SBuffer Underrun error message is displayed Track-at-Once TAO AppendixWriting Modes Disc-at-Once DAOPacket Writing Session-at-Once SAOAppendix URL for Yamaha CD-R/RW Drives web sites Europe About firmwareStatus Ndicator essages LED olor LED Indicator MessagesCD-RW CRW2200 drive CRW2200 series complies with the following specifications Index SymbolsPhillips Screwdriver 12, 32 Russia EUROPE, Eastern Europe