Yamaha CRW2200S manual Warranty

Page 7

About CD-R/RW discs

Please read the following regarding the handling of CD-R/RW discs.

1.Do not expose discs to excessive heat, such as in areas subject to direct sunlight or near a heater.

Also, avoid keeping them in a humid place.

2.Do not touch the surface of a disc.

When handling a disc, hold it by its edges.

3.Remove dust and dirt from the surface of a disc.

Use air-based dust removers. The surface of a disc may be scratched if wiped with a dry cloth.

4.Do not stick labels on the surface of a disc.

5.Do not write on the surface of a disc except where indicated.

6.Do not clean discs with chemicals or detergents.

7.Do not bend or drop discs.

8.Do not use irregularly shaped discs, such as a star or a heart or a card shaped, etc. Such discs could damage your new CD-R/RW drive. (Use only circular discs.)

1.The information contained in this manual is subject to change without prior notice.

2.All trademarks contained in this manual belong to their respective owners.

3.Yamaha does not bear any responsibility for any outcome as a result of using this device.

4.Reproduction of this manual, either in part or in full, is expressly forbidden.

Precautions for Transportation

Before transporting the device, always put it in its original box. If the device is transported without adequate packing, the internal components may be damaged and cause the device to malfunction.

Copyrights

When writing to CD-R/RW, make sure that you are not infringing any copyrights. It is illegal to copy audio CDs for non-personal use. When backing up software, please make sure that you are not infringing any software copyrights for that product.

WARRANTY

YAMAHA AND SUPPLIERS ACCEPT NO LIABILITY FOR THE LOSS OF ANY DATA OR ANY PROBLEMS CAUSED AS A RESULT. AS A PRECAUTION, IT IS RECOMMENDED THAT THE DISCS BE TESTED AFTER THEY HAVE BEEN WRITTEN TO.

FURTHERMORE, UNDER NO CIRCUMSTANCES DOES YAMAHA AND SUPPLIERS GUARANTEE THE RELIABILITY OF THE DISCS.

iv

Image 7
Contents Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents → E-IDE Atapi Connection Set Up P → Scsi Connection Set Up PScsi convertor Introduction Features of the CRW2200 driveYamaha Buffer Underrun Protection Buffer Underrun DefinedIntroduction System Requirements Before UseThese are also required for Scsi connection High Speed CD-RW discs*3 Supported DiscsCD-R discs*1 CD-RW discs*2About Partial CAV Constant Angular Velocity About CD-ROMsAbout 10X-speed writing/rewriting of a High Speed CD-RW disc Serial number Letters and 7 digits Serial NumberFront Panel Front and Rear of UnitRear Panel with the Scsi Convertor ➄ DC Input connector ➀ Digital Audio OUT connector➁ Analog Audio OUT connector ➂ Jumper switchLong-Nosed Pliers Scsi Connection Set UpTools Phillips ScrewdriverScsi Connection Set Up CRW2200S Setup FlowchartCover Front panel Connecting the CRW2200SOpening the Computer Shut down your computer and unplug it from the AC outletDischarge any static charge Left L Ground G Right R Audio cable To Sound card Connecting the analog audio cableAudio cable connection Connect the audio cable to the CRW2200 drive. If necessaryGround G Signal D Digital audio cable To Sound card Connecting the digital audio cableScrew Installing the Scsi Convertor to the CRW2200 driveDC Input Yellow wireJumper switches Setting the Jumper SwitchesRear Panel Scsi ID ➀ Scsi ID Number➂ Termination ➁ Parity CheckWorkstation Block size OFF Default Block size onSet to on when installing ➃ Block SizeChoosing the Connection Method As a replacement driveCD-ROM drive Audio cable Pin IDE cable Pin power cable Installing the CRW2200SInch drive bay slot Front cover Motherboard Colored line connector Scsi connector 50-pin Scsi flat cableSpdif Digital audio cable Sound cardTop Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on For Windows NT Configuring for the Operating SystemInstall the CD writing software Installing the CD Writing SoftwareRemoving the Scsi convertor Removing the Scsi convertorRemoving the Scsi convertor Audio cable Pin Scsi flat cable Pin power cableRemove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up IDE Atapi Connection Set Up CRW2200E Setup FlowchartConnecting the CRW2200E Choosing the Connection Method About IDE Typical IDE-type hardware installationSlave Motherboard Primary Master Secondary SlaveMaster Example-1 As secondary slave For supplemental drive Connecting examplesIDE Atapi Connection Set Up Rear Panel Master Slave factory setting About the Csel jumper switchAs an supplemental drive Installing the CRW2200EConnect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Loading a Disc OperationEjecting a Disc Operation Ejecting a Disc in an EmergencyManual Eject hole Paper Clip Yamaha CD-R/RW Drives web site URL Europe TroubleshootingTroubleshooting Disc keeps being ejected Setting of the Windows Media Player Properties setting of the CRW2200SBuffer Underrun error message is displayed Track-at-Once TAO AppendixWriting Modes Disc-at-Once DAOPacket Writing Session-at-Once SAOAppendix URL for Yamaha CD-R/RW Drives web sites Europe About firmwareStatus Ndicator essages LED olor LED Indicator MessagesCD-RW CRW2200 drive CRW2200 series complies with the following specifications Index SymbolsPhillips Screwdriver 12, 32 Russia EUROPE, Eastern Europe