Yamaha CRW2200S manual Connecting the digital audio cable, Ground G Signal D Digital audio cable

Page 53

E-IDE (ATAPI) Connection Set Up

Note

Some sound cards may have one or more audio input connectors.

However, depending on your connectors, the specifications may differ from the CRW2200E. If no sound is audible from the speaker even though the audio cable is connected, refer to the documentation that came with your sound card for more details, and make sure that your audio cable is connected correctly.

The ANALOG AUDIO OUT connector of the CRW2200E is shown in the figure on the previous page.

Connecting the digital audio cable

The digital connection for the CRW2200E is ideal for pure quality audio playback, outputting digital signals recorded on CDs to the sound card without any distortion.

Examples of the digital connection

To output digital audio signals to external devices, you must use the digital connection to connect the unit and the sound card. With this connection you can:

Enjoy music using a digital audio amplifier.

Record music digitally with an MD player.

Use the digital audio cable to connect the DIGITAL AUDIO OUT connector of the unit and the SPDIF input connector (digital audio) of the sound card, making sure of the connector’s direction.

DIGITAL AUDIO

OUT

Ground (G)

Signal (D)

Digital audio cable

SPDIF

Sound card

Note

For the digital connection, you need a digital audio cable with appropriate connectors, and a sound card with SPDIF (digital audio) input connectors.

The DIGITAL AUDIO OUT connector of the CRW2200E is shown in the figure above.

45

Image 53
Contents Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents Scsi convertor → Scsi Connection Set Up P→ E-IDE Atapi Connection Set Up P Introduction Features of the CRW2200 driveIntroduction Buffer Underrun DefinedYamaha Buffer Underrun Protection These are also required for Scsi connection Before UseSystem Requirements CD-R discs*1 Supported DiscsCD-RW discs*2 High Speed CD-RW discs*3About Partial CAV Constant Angular Velocity About CD-ROMsAbout 10X-speed writing/rewriting of a High Speed CD-RW disc Serial number Letters and 7 digits Serial NumberFront Panel Front and Rear of UnitRear Panel with the Scsi Convertor ➁ Analog Audio OUT connector ➀ Digital Audio OUT connector➂ Jumper switch ➄ DC Input connectorTools Scsi Connection Set UpPhillips Screwdriver Long-Nosed PliersScsi Connection Set Up CRW2200S Setup FlowchartOpening the Computer Connecting the CRW2200SShut down your computer and unplug it from the AC outlet Cover Front panelDischarge any static charge Audio cable connection Connecting the analog audio cableConnect the audio cable to the CRW2200 drive. If necessary Left L Ground G Right R Audio cable To Sound cardGround G Signal D Digital audio cable To Sound card Connecting the digital audio cableScrew Installing the Scsi Convertor to the CRW2200 driveDC Input Yellow wireRear Panel Setting the Jumper SwitchesJumper switches Scsi ID ➀ Scsi ID Number➂ Termination ➁ Parity CheckSet to on when installing Block size OFF Default Block size on➃ Block Size WorkstationCD-ROM drive As a replacement driveChoosing the Connection Method Inch drive bay slot Front cover Installing the CRW2200SAudio cable Pin IDE cable Pin power cable Motherboard Colored line connector Scsi connector 50-pin Scsi flat cableSpdif Digital audio cable Sound cardTop Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on For Windows NT Configuring for the Operating SystemInstall the CD writing software Installing the CD Writing SoftwareRemoving the Scsi convertor Removing the Scsi convertorRemoving the Scsi convertor Audio cable Pin Scsi flat cable Pin power cableRemove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up IDE Atapi Connection Set Up CRW2200E Setup FlowchartConnecting the CRW2200E Choosing the Connection Method Slave Motherboard Primary Master Secondary SlaveMaster Typical IDE-type hardware installationAbout IDE Example-1 As secondary slave For supplemental drive Connecting examplesIDE Atapi Connection Set Up Rear Panel Master Slave factory setting About the Csel jumper switchAs an supplemental drive Installing the CRW2200EConnect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Ejecting a Disc OperationLoading a Disc Manual Eject hole Paper Clip Ejecting a Disc in an EmergencyOperation Yamaha CD-R/RW Drives web site URL Europe TroubleshootingTroubleshooting Disc keeps being ejected Setting of the Windows Media Player Properties setting of the CRW2200SBuffer Underrun error message is displayed Writing Modes AppendixDisc-at-Once DAO Track-at-Once TAOAppendix Session-at-Once SAOPacket Writing URL for Yamaha CD-R/RW Drives web sites Europe About firmwareStatus Ndicator essages LED olor LED Indicator MessagesCD-RW CRW2200 drive CRW2200 series complies with the following specifications Index SymbolsPhillips Screwdriver 12, 32 Russia EUROPE, Eastern Europe