Yamaha CRW2200S manual Motherboard, Colored line connector Scsi connector 50-pin Scsi flat cable

Page 34

SCSI Connection Set Up

The following explains how to add the drive to the computer as illustrated.

If you are replacing the existing CD-ROM drive, the procedure is basically the same.

Note

The way of installing built-in devices may differ, depending on the computer. Refer also to the documentation that came with your computer.

11Slide the drive backwards into the slot, then tighten the four fastening screws on the sides of the unit to hold the drive in place.

Notes

•Do not apply excessive force when sliding the drive backwards into the drive bay slot.

•Leave enough room behind the drive to connect the power, SCSI, and audio cables.

12Connect the 50-pin SCSI flat cable to the computer’s SCSI card and to the SCSI INTERFACE connector on the rear panel of the CRW2200S. Be sure to plug in the cable so that the colored line on the cable corresponds to the pin 1 on the right end of the connector as shown in the figure below. The pin 1 of the CRW2200S is positioned in the right part of the SCSI connector. The pin 1 of the SCSI connector is labeled on the SCSI card, or refer to the documentation that came with your SCSI card.

Motherboard

SCSI INTERFACE

Colored line connector

Colored line

SCSI connector 50-pin SCSI flat cable

26

Image 34

Contents Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents → E-IDE Atapi Connection Set Up P → Scsi Connection Set Up PScsi convertor Features of the CRW2200 drive IntroductionYamaha Buffer Underrun Protection Buffer Underrun DefinedIntroduction System Requirements Before UseThese are also required for Scsi connection CD-RW discs*2 Supported DiscsCD-R discs*1 High Speed CD-RW discs*3About CD-ROMs About Partial CAV Constant Angular VelocityAbout 10X-speed writing/rewriting of a High Speed CD-RW disc Serial Number Serial number Letters and 7 digitsFront and Rear of Unit Front PanelRear Panel with the Scsi Convertor ➂ Jumper switch ➀ Digital Audio OUT connector➁ Analog Audio OUT connector ➄ DC Input connectorPhillips Screwdriver Scsi Connection Set UpTools Long-Nosed PliersCRW2200S Setup Flowchart Scsi Connection Set UpShut down your computer and unplug it from the AC outlet Connecting the CRW2200SOpening the Computer Cover Front panelDischarge any static charge Connect the audio cable to the CRW2200 drive. If necessary Connecting the analog audio cableAudio cable connection Left L Ground G Right R Audio cable To Sound cardConnecting the digital audio cable Ground G Signal D Digital audio cable To Sound cardInstalling the Scsi Convertor to the CRW2200 drive ScrewYellow wire DC InputJumper switches Setting the Jumper SwitchesRear Panel ➀ Scsi ID Number Scsi ID➁ Parity Check ➂ Termination➃ Block Size Block size OFF Default Block size onSet to on when installing WorkstationChoosing the Connection Method As a replacement driveCD-ROM drive Audio cable Pin IDE cable Pin power cable Installing the CRW2200SInch drive bay slot Front cover Colored line connector Scsi connector 50-pin Scsi flat cable MotherboardDigital audio cable Sound card SpdifTop Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on Configuring for the Operating System For Windows NTInstalling the CD Writing Software Install the CD writing softwareRemoving the Scsi convertor Removing the Scsi convertorAudio cable Pin Scsi flat cable Pin power cable Removing the Scsi convertorRemove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up CRW2200E Setup Flowchart IDE Atapi Connection Set UpConnecting the CRW2200E Choosing the Connection Method About IDE Typical IDE-type hardware installationSlave Motherboard Primary Master Secondary SlaveMaster Connecting examples Example-1 As secondary slave For supplemental driveIDE Atapi Connection Set Up About the Csel jumper switch Rear Panel Master Slave factory settingInstalling the CRW2200E As an supplemental driveConnect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Loading a Disc OperationEjecting a Disc Operation Ejecting a Disc in an EmergencyManual Eject hole Paper Clip Troubleshooting Yamaha CD-R/RW Drives web site URL EuropeTroubleshooting Disc keeps being ejected Properties setting of the CRW2200S Setting of the Windows Media PlayerBuffer Underrun error message is displayed Disc-at-Once DAO AppendixWriting Modes Track-at-Once TAOPacket Writing Session-at-Once SAOAppendix About firmware URL for Yamaha CD-R/RW Drives web sites EuropeLED Indicator Messages Status Ndicator essages LED olorCD-RW CRW2200 drive CRW2200 series complies with the following specifications Symbols IndexPhillips Screwdriver 12, 32 EUROPE, Eastern Europe Russia