Yamaha CRW2200S manual Connect the audio cable. If necessary, Connecting the analog audio cable

Page 52

E-IDE (ATAPI) Connection Set Up

9Connect the audio cable. (If necessary)

You can play audio CDs on the CRW2200E and listen through your computer’s sound card.

Notes

•Audio is available from the headphones or speakers connected to the headphone jack located on the front panel of the CRW2200E (this is convenient if you have no sound card in your computer). In this case, you do not need to connect an audio cable.

•When creating an audio CD, if you use the IDE cable to send the signal, you do not need to connect an audio cable.

•If you use the CRW2200E as a supplemental drive for the unit, and the CD-ROM drive or DVD-ROM drive is already connected to the sound card, YAMAHA recommends you playback audio CDs using the existing drive.

There are two methods of connecting the unit and the sound card: an analog connection and a digital connection.

Connecting the analog audio cable

Connect one end (the end which has one connector) of the included audio cable to the ANALOG AUDIO OUT connector on the rear panel of the CRW2200E. Make sure to check the connector direction according to the figure below.

There are two connectors at the opposite end of the audio cable: a vertically- mounted type (PH) and a horizontally-mounted type (MPC). Choose the one that matches your soundcard’s connector and leave the other free.

ANALOG AUDIO

OUT

Left (L)

Ground (G)

Right (R)

Audio cable

Vertically- mounted type (PH)

Audio input connector

Horizontally- mounted type (MPC)

Sound card

44

Image 52

Contents Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents → E-IDE Atapi Connection Set Up P → Scsi Connection Set Up PScsi convertor Features of the CRW2200 drive IntroductionYamaha Buffer Underrun Protection Buffer Underrun DefinedIntroduction System Requirements Before UseThese are also required for Scsi connection Supported Discs CD-R discs*1CD-RW discs*2 High Speed CD-RW discs*3About CD-ROMs About Partial CAV Constant Angular VelocityAbout 10X-speed writing/rewriting of a High Speed CD-RW disc Serial Number Serial number Letters and 7 digitsFront and Rear of Unit Front PanelRear Panel with the Scsi Convertor ➀ Digital Audio OUT connector ➁ Analog Audio OUT connector➂ Jumper switch ➄ DC Input connectorScsi Connection Set Up ToolsPhillips Screwdriver Long-Nosed PliersCRW2200S Setup Flowchart Scsi Connection Set UpConnecting the CRW2200S Opening the ComputerShut down your computer and unplug it from the AC outlet Cover Front panelDischarge any static charge Connecting the analog audio cable Audio cable connectionConnect the audio cable to the CRW2200 drive. If necessary Left L Ground G Right R Audio cable To Sound cardConnecting the digital audio cable Ground G Signal D Digital audio cable To Sound cardInstalling the Scsi Convertor to the CRW2200 drive ScrewYellow wire DC InputJumper switches Setting the Jumper SwitchesRear Panel ➀ Scsi ID Number Scsi ID➁ Parity Check ➂ TerminationBlock size OFF Default Block size on Set to on when installing➃ Block Size WorkstationChoosing the Connection Method As a replacement driveCD-ROM drive Audio cable Pin IDE cable Pin power cable Installing the CRW2200SInch drive bay slot Front cover Colored line connector Scsi connector 50-pin Scsi flat cable MotherboardDigital audio cable Sound card SpdifTop Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on Configuring for the Operating System For Windows NTInstalling the CD Writing Software Install the CD writing softwareRemoving the Scsi convertor Removing the Scsi convertorAudio cable Pin Scsi flat cable Pin power cable Removing the Scsi convertorRemove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up CRW2200E Setup Flowchart IDE Atapi Connection Set UpConnecting the CRW2200E Choosing the Connection Method About IDE Typical IDE-type hardware installationSlave Motherboard Primary Master Secondary SlaveMaster Connecting examples Example-1 As secondary slave For supplemental driveIDE Atapi Connection Set Up About the Csel jumper switch Rear Panel Master Slave factory settingInstalling the CRW2200E As an supplemental driveConnect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Loading a Disc OperationEjecting a Disc Operation Ejecting a Disc in an EmergencyManual Eject hole Paper Clip Troubleshooting Yamaha CD-R/RW Drives web site URL EuropeTroubleshooting Disc keeps being ejected Properties setting of the CRW2200S Setting of the Windows Media PlayerBuffer Underrun error message is displayed Appendix Writing ModesDisc-at-Once DAO Track-at-Once TAOPacket Writing Session-at-Once SAOAppendix About firmware URL for Yamaha CD-R/RW Drives web sites EuropeLED Indicator Messages Status Ndicator essages LED olorCD-RW CRW2200 drive CRW2200 series complies with the following specifications Symbols IndexPhillips Screwdriver 12, 32 EUROPE, Eastern Europe Russia