Yamaha CRW2200S manual Remove the Scsi convertor from the CRW2200 drive

Page 42

Removing the SCSI convertor

6Remove the SCSI convertor from the CRW2200 drive.

SCSI convertor

7Disconnect the power cable from the SCSI convertor and the CRW2200 drive.

The smaller connector connected to the SCSI convertor is locked with its hook. Lift up the connector to unlock the hook, then pull it out. (See the figure below.) If the audio cable is connected, disconnect it after removing the convertor.

(An analog audio cable connection is shown in the figure below.)

Analog audio cable

Smaller connector

Bigger connector

Power cable

34

Image 42
Contents Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents → Scsi Connection Set Up P → E-IDE Atapi Connection Set Up PScsi convertor Features of the CRW2200 drive IntroductionBuffer Underrun Defined Yamaha Buffer Underrun ProtectionIntroduction Before Use System RequirementsThese are also required for Scsi connection CD-RW discs*2 Supported DiscsCD-R discs*1 High Speed CD-RW discs*3About CD-ROMs About Partial CAV Constant Angular VelocityAbout 10X-speed writing/rewriting of a High Speed CD-RW disc Serial Number Serial number Letters and 7 digitsFront and Rear of Unit Front PanelRear Panel with the Scsi Convertor ➂ Jumper switch ➀ Digital Audio OUT connector➁ Analog Audio OUT connector ➄ DC Input connectorPhillips Screwdriver Scsi Connection Set UpTools Long-Nosed PliersCRW2200S Setup Flowchart Scsi Connection Set UpShut down your computer and unplug it from the AC outlet Connecting the CRW2200SOpening the Computer Cover Front panelDischarge any static charge Connect the audio cable to the CRW2200 drive. If necessary Connecting the analog audio cableAudio cable connection Left L Ground G Right R Audio cable To Sound cardConnecting the digital audio cable Ground G Signal D Digital audio cable To Sound cardInstalling the Scsi Convertor to the CRW2200 drive ScrewYellow wire DC InputSetting the Jumper Switches Jumper switchesRear Panel ➀ Scsi ID Number Scsi ID➁ Parity Check ➂ Termination➃ Block Size Block size OFF Default Block size onSet to on when installing WorkstationAs a replacement drive Choosing the Connection MethodCD-ROM drive Installing the CRW2200S Audio cable Pin IDE cable Pin power cableInch drive bay slot Front cover Colored line connector Scsi connector 50-pin Scsi flat cable MotherboardDigital audio cable Sound card SpdifTop Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on Configuring for the Operating System For Windows NTInstalling the CD Writing Software Install the CD writing softwareRemoving the Scsi convertor Removing the Scsi convertorAudio cable Pin Scsi flat cable Pin power cable Removing the Scsi convertorRemove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up CRW2200E Setup Flowchart IDE Atapi Connection Set UpConnecting the CRW2200E Choosing the Connection Method Typical IDE-type hardware installation About IDESlave Motherboard Primary Master Secondary SlaveMaster Connecting examples Example-1 As secondary slave For supplemental driveIDE Atapi Connection Set Up About the Csel jumper switch Rear Panel Master Slave factory settingInstalling the CRW2200E As an supplemental driveConnect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Operation Loading a DiscEjecting a Disc Ejecting a Disc in an Emergency OperationManual Eject hole Paper Clip Troubleshooting Yamaha CD-R/RW Drives web site URL EuropeTroubleshooting Disc keeps being ejected Properties setting of the CRW2200S Setting of the Windows Media PlayerBuffer Underrun error message is displayed Disc-at-Once DAO AppendixWriting Modes Track-at-Once TAOSession-at-Once SAO Packet WritingAppendix About firmware URL for Yamaha CD-R/RW Drives web sites EuropeLED Indicator Messages Status Ndicator essages LED olorCD-RW CRW2200 drive CRW2200 series complies with the following specifications Symbols IndexPhillips Screwdriver 12, 32 EUROPE, Eastern Europe Russia