3Com EISA 10/100BASE-T manual Alternatively, at the prompt, type

Page 34

Loading NetWare ODI Drivers

4-5

2Insert the 3C59X EtherDisk diskette in a ﬂoppy drive on your computer and make that drive the current drive.

For example, if the diskette is in drive A, type the following command:

A:[Enter]

3At the prompt, type:

INSTALL [Enter]

Alternatively, at the prompt, type:

AUTOLINK [Enter]

If you type AUTOLINK instead of INSTALL, you will bypass the EtherDisk diskette menu program (skipping steps 5 and 6) and advance to step 7.

4The ﬁrst time you use the diskette to install an adapter, a license screen appears. To accept the terms and conditions of the 3Com end-user software license agreement, type the following:

Y

To view the full text of the license agreement, press [F1].

Once you have agreed to the terms and conditions of the 3Com license agreement, the license information screen will not appear again.

The Auto Installation Information screen appears, as shown in Figure 4-2.

5Read the screen and press [Enter].

6When the main menu screen shown in Figure 4-3 appears, select NetWare DOS ODI Client, and press [Enter].

Auto installation takes a few minutes. The AutoLink program makes changes to your AUTOEXEC.BAT and CONFIG.SYS ﬁles. Several messages appear while the program is running. A ﬁnal message indicating successful installation appears.

Image 34

Contents User Guide Fast Etherlink Parallel TaskingNetwork Adapter Adapters3Com Corporation 5400 Bayfront Plaza Santa Clara, California Lifetime Warranty France, Israel Contents Loading Network Drivers Cispr B Compliance Figures Tables About this Guide How to Use This GuideIntroduction Conventions Print Autolink.logIntroduction Adapter FeaturesSingle-slot, 32-bit half-card Procedures described in this guide are shown in Figure Procedure OverviewInstalling the Hardware Hardware Installation OverviewInspecting the Adapter Installing the Boot PromInserting the Fast EtherLink Eisa Adapter Computer with PCI and Eisa Slots Name of the installed 3Com adapter appears, as shown below Conﬁrming Adapter InstallationList of devices appears, arranged by type Connecting to the Network Installing the Hardware Auto Select Media Type Configuring the Adapter Adapter Conﬁguration OverviewUsing a NOS Other Than Windows Conﬁguring the AdapterUsing Windows Software Option Settings Complete one of the following instructionsFull Duplex Media TypeNetwork Driver Optimization Multitasking environments, choosingChanging the Settings At the prompt, typeI N N U Second dialog box appears Continue this procedure with any of the other optionsPress Tab to highlight OK. Press Enter Select Adapter Installed Adapters Loading Network DriversAccessing DOS Locating the Network DriversLoading NetWare ODI Drivers Describes how to access DOS from various operating systemsOne Eisa Adapter in a Client Loading Network Drivers Alternatively, at the prompt, type To view the full text of the license agreement, press F1Have only one 3Com Bus Master adapter installed Multiple Eisa Adapters in a Client To print the ﬁle, typeWhen the program has ﬁnished a Save the conﬁguration Repeat a for the second adapter Reboot the computer Finding the Adapter’s Slot NumberMain menu appears One Eisa Adapter in a Server Multiple Eisa Adapters in a Server Loading NetWare ODI DriversFinding the Adapter’s Port Address for Multiple Adapters For NetWare 3.12, 4.0, or For the latest NLMs, contact NovellLoading Non-NetWare Drivers Loading Windows 95 DriversTo load other types of network drivers, follow these steps Windows NT, version Ndis DriversNdis Windows for Workgroups WindowsDesktop Management Interface Transcend PC Link SmartAgent Driver AgentsAdditional Drivers Performing Troubleshooting Diagnostic Tests Illustrates how the procedures in this chapter might be usedDiagnostic Tests Overview Before Running the TestsStarting the Diagnostic Program Types of TestsTo run the Group 1 tests, follow these steps Command Line AccessRunning the Group 1 Tests Press Enter to start the testsRunning the Group 3 Test Mbps or 100 MbpsSetting Up an Echo Server Enable the Group 3 test by selecting the Enable Group button Getting Help If a Test Fails Changing the Test Setup To change the test parameters, follow these stepsMiscellaneous Checks LEDs LEDPerforming Troubleshooting and Diagnostic Tests CSMA/CD local area network SpecificationsAdapter Card Speciﬁcations Local area networkCabling Requirements RJ-45 Connector Pin AssignmentsWhen properly connected to a 10BASE-T network, Maximum UTP cable distance is 100 meters at either speedAccess by Modem On-line Technical Services3Com Bulletin Board Service Technical SupportThreeComForum on CompuServe 3ComFacts Automated Fax ServiceWorld Wide Web Site To use ThreeComForum Log on to CompuServeLocal numbers are available within the following countries Support from Your Network SupplierDetails about recent conﬁguration changes, if applicable Returning Products for Repair To obtain an RMA number, call or faxGlossary AUI cableBus BackboneBackplane DriverEMM386 Echo serverEthernet Transceiver Parallel TaskingServer Twisted-pairIndex SymbolsNumerics Diagnostic tests NLMs 4-10, 4-12 NETWARE\SERVER subdirectory 4-11 network Limited Warranty 3Com Corporation Bayfront Plaza Interference Handbook Cispr B Compliance