3Com EISA 10/100BASE-T manual Backbone, Backplane, Bus, Driver

Page 65

2GLOSSARY

data transmission. This function is implemented by all NetWare ODI drivers, Windows for Workgroups drivers, NDIS 2.01 drivers, and Windows NT and Windows 95 drivers.

Backbone

The main transmission medium used to interconnect the workgroup areas of a network. It is usually coaxial or fiber.

Backplane

A motherboard assembly in a PC with connectors and printed circuit traces into which printer circuit boards are inserted.

Bus

An electronic pathway along which signals are transmitted from one area of a computer to another.

Bus master adapter

An adapter that contains its own processor, which allows the adapter to operate independently of the computer’s main processor.

Coaxial cable

An electrical wire consisting of two primary electrical elements: an outer braided wire that acts as a ground and an inner one used to carry signals.

Configuration

The software settings that allow different hardware components of a computer system to communicate with one another.

CSMA/CD

Carrier Sense Multiple Access with Collision Detection. A baseband protocol with a built-in collision-detection technique.

Driver

A program, usually resident in server or workstation memory, that controls the network hardware (such as adapters or controllers) or implements the protocol stacks through which higher-level applications communicate with the network hardware.

Image 65
Contents Network Adapter Fast Etherlink Parallel TaskingUser Guide Adapters3Com Corporation 5400 Bayfront Plaza Santa Clara, California Lifetime Warranty France, Israel Contents Loading Network Drivers Cispr B Compliance Figures Tables Introduction How to Use This GuideAbout this Guide Print Autolink.log ConventionsSingle-slot, 32-bit half-card Adapter FeaturesIntroduction Procedure Overview Procedures described in this guide are shown in FigureHardware Installation Overview Installing the HardwareInserting the Fast EtherLink Eisa Adapter Installing the Boot PromInspecting the Adapter Computer with PCI and Eisa Slots List of devices appears, arranged by type Confirming Adapter InstallationName of the installed 3Com adapter appears, as shown below Connecting to the Network Installing the Hardware Auto Select Media Type Adapter Configuration Overview Configuring the AdapterConfiguring the Adapter Using a NOS Other Than WindowsUsing Windows Complete one of the following instructions Software Option SettingsNetwork Driver Optimization Media TypeFull Duplex Multitasking environments, choosingAt the prompt, type Changing the SettingsI N N U Press Tab to highlight OK. Press Enter Continue this procedure with any of the other optionsSecond dialog box appears Select Adapter Installed Adapters Drivers Loading NetworkLocating the Network Drivers Accessing DOSOne Eisa Adapter in a Client Describes how to access DOS from various operating systemsLoading NetWare ODI Drivers Loading Network Drivers To view the full text of the license agreement, press F1 Alternatively, at the prompt, typeHave only one 3Com Bus Master adapter installed To print the file, type Multiple Eisa Adapters in a ClientWhen the program has finished a Save the configuration Main menu appears Reboot the computer Finding the Adapter’s Slot NumberRepeat a for the second adapter One Eisa Adapter in a Server Loading NetWare ODI Drivers Multiple Eisa Adapters in a ServerFinding the Adapter’s Port Address for Multiple Adapters For the latest NLMs, contact Novell For NetWare 3.12, 4.0, orTo load other types of network drivers, follow these steps Loading Windows 95 DriversLoading Non-NetWare Drivers Ndis Windows for Workgroups Ndis DriversWindows NT, version WindowsAdditional Drivers Transcend PC Link SmartAgent Driver AgentsDesktop Management Interface Illustrates how the procedures in this chapter might be used Performing Troubleshooting Diagnostic TestsBefore Running the Tests Diagnostic Tests OverviewTypes of Tests Starting the Diagnostic ProgramRunning the Group 1 Tests Command Line AccessTo run the Group 1 tests, follow these steps Press Enter to start the testsMbps or 100 Mbps Running the Group 3 TestSetting Up an Echo Server Enable the Group 3 test by selecting the Enable Group button Getting Help If a Test Fails To change the test parameters, follow these steps Changing the Test SetupMiscellaneous Checks LED LEDsPerforming Troubleshooting and Diagnostic Tests Adapter Card Specifications SpecificationsCSMA/CD local area network Local area networkWhen properly connected to a 10BASE-T network, RJ-45 Connector Pin AssignmentsCabling Requirements Maximum UTP cable distance is 100 meters at either speed3Com Bulletin Board Service On-line Technical ServicesAccess by Modem Technical SupportWorld Wide Web Site 3ComFacts Automated Fax ServiceThreeComForum on CompuServe To use ThreeComForum Log on to CompuServeDetails about recent configuration changes, if applicable Support from Your Network SupplierLocal numbers are available within the following countries To obtain an RMA number, call or fax Returning Products for RepairAUI cable GlossaryBackplane BackboneBus DriverEthernet Echo serverEMM386 Server Parallel TaskingTransceiver Twisted-pairNumerics SymbolsIndex Diagnostic tests NLMs 4-10, 4-12 NETWARE\SERVER subdirectory 4-11 network Limited Warranty 3Com Corporation Bayfront Plaza Interference Handbook Cispr B Compliance