Cisco Systems 4.2(1) Configuring permissions for installation directory, Creating a new web site

Page 64

Configuring permissions for installation directory

For security reasons, change the permissions for the installation directory. In a distributed installation, carry out these tasks on the file server.

To configure permissions:

1.Remove permissions to everyone from the cisco share.

2.Give full control to the domain user account that you had created earlier for Cisco Interaction Manager services (page 16).

Configuring a web site for the messaging applet

When the application is accessed, a messaging applet is launched in the browser. This applet gets messages for the user from the database.

Important: You need to perform these tasks only if you are using a load balancer in your

installation and your installation includes Unified WIM.

This section explains the procedures that you must perform to configure a new web site for the messaging applet. These include:

Creating a new web site

Verifying messaging applet web site

Configuring the properties of the new web site

Creating virtual directories

Configuring the Applet host setting

Creating a new web site

You need to create a new web site for the messaging applet. From here on in the document, the new web site is referred to as Messaging Applet web site.

Important: Before you start, get another IP address assigned to the web server. Make sure that both the IP addresses map to the same LAN card. Also, get a fully qualified domain name for the new IP address.

To configure a new web site:

1.Go to Start > Settings > Control Panel > Administrative Tools > Internet Information Services.

2.Browse to Web Sites.

3.Right-clickWeb Sites and click New > Web Site.

64 Cisco Unified Web and E-Mail Interaction Manager Installation Guide

Image 64

Contents For Unified Contact Center Express Page Contents Installation process About partitions Installing business partitions 104 Preface About this guide Document conventionsOnline help Other learning resourcesDocument set Planning Configuration options Additional partitions Pre-installation Tasks To set up the required software environment Verifying system requirementsBandwidth and hardware requirements Software requirementsConfiguring environment variables Verifying SQL Server authentication settingsTo verify the authentication mode of SQL Server Collecting required informationVerifying state of Microsoft Search service Setting up user accounts and permissionsTo verify the state of the Microsoft Search service To set up user accounts and permissionsCreating WebLogic domains Verifying directory namesTo verify directory names Choose configuration template Create administrative user Creating WebLogic domains for secondary application servers Choose custom configuration Configure the administration server Database Jdbc Options window, select No Configure Windows Options window, select No for both options Configure server start mode and Java SDK Configuring virus scanner Verifying Network ConfigurationVerifying Unified CCX installation Verifying WebLogic domainsInstallation Process Installing a single-server or collocated configuration To install a single-server or collocated configurationInstallation process Type the path or browse to the JDK home directory BEAHome\userprojects\domains\DomainName Provide WebLogic server and RMI parameters Dont provide the host name, the installation will fail Provide master database parameters Provide partition database parameters Welcome window, read the introduction and click Next Additional steps for collocated configurations To install the web serverInstalling a distributed-server configuration Installing a split-server or collocated configurationTo install a split-server or collocated configuration Installing the database To install the databaseCreate the first system administrator user account Dont provide the host name, the installation will fail Installing the primary application server and file server To install the primary application server and file server File Server  Application Server Type the path to or browse to the JDK home directory Provide the names of the web server and services server Dont provide the host name, the installation will fail Provide partition database parameters Welcome window, read the introduction and click Next Installing secondary application servers To install a secondary application serverInstalling the web server Provide file server parameters Installing the services server To install the services serverType the name of the file server Post-installation Tasks Setting up archives for partition databases Applying updatesChanging web server settings Configuring Internet Information Services Shutdown worker process after being idle for Configuring pool thread limit To configure pool thread limitConfiguring content expiration settings RegeditRemoving extension mapping To configure content expirationTo remove extension mapping Changing authentication settings for web site To change authentication settings for the web siteClick the Edit button To change the network directory security settings Changing security credentials for network directoryChanging logon parameters for Cisco service To change the logon parametersConfiguring permissions for installation directory Configuring a web site for the messaging appletTo configure permissions To configure a new web siteProvide a name for the web site Verifying messaging applet web site To verify the messaging applet web siteConfiguring web site properties To configure the propertiesCreating virtual directories To create a virtual directory\\FileServerName\CiscoHome\eService. Click Next Configuring the Applet host setting To configure the Applet host settingSetting up secure socket layer Separating the web server from the application serverStarting and stopping Cisco Interaction Manager To separate the web server from the application serverLogging in to the business partition Logging in from Internet ExplorerLogging in from Cisco Agent Desktop Embedded Browser To stop Cisco Interaction ManagerConfiguring some important settings Mandatory settingsAt the partition level At the department levelOptional settings Uninstalling Cisco Interaction ManagerTo uninstall Cisco Interaction Manager Click the Uninstall button Additional partitions About partitions Installing business partitionsTo create a new business partition Installation Options window, select the Partition option Provide web server parameters Dont provide the host name, the installation will fail Archives Setting up the archive for a partition Enabling network DTC accessTo enable network DTC access About archivesSetting up the archive To set up the archiveInstallation Options window, select the Archive option Provide partition parameters Provide archive database parameters SSL for secure Connections Generating a security certificate request Installing a security certificateTo generate a certificate request Select the Create a new certificate option Provide information about your organization Submitting the certificate request Installing the certificate on the web server To install the certificate on the web serverSSL Port window, specify the SSL port for the web site Configuring SSL access To configure SSL accessConfiguring the viewing of attachments Testing SSL accessTo enable users to view attachments To test SSL access to Unified WIM and Unified EIMHttps//WebServer/Partition Configuration details Configuration type and optionFile server details Database detailsMaster database parameters Application server details Unified CCX Data Integration Wizard details Web server details Services server detailsArchive details Additional partition details Make sure you provide the DNS host Appendix B Path to Maintenance Release Appendix B Path to Maintenance Release 4.25